|
|
零件编号 | TM040YDHG32 | ||
描述 | Display Module | ||
制造商 | Tianma | ||
LOGO | |||
1 Page
Model No.TM040YDHG32
MODEL NO. :
ISSUED DATE:
VERSION :
TM040YDHG32
2014-4-16
V1.0
■Preliminary Specification
□Final Product Specification
Customer :
Approved by
Notes
TIANMA Confirmed :
Prepared by
Checked by
Approved by
This technical specification is subjected to change without notice
The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation
and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of
TIANMA MICRO-ELECTRONICS Corporation.
Page 1 of 21
4.4 Block Diagram
5 LCD PANEL
6
7
8
9 3.97inch
10 480 (RGB) X800
11
12
13
14
15
16
17
BLU
23
Model No.TM040YDHG32
RAM
Source+ Gate
Driver
VCOM&
TCON
DSI_D0P、DSI_D0N,
DSI_D1P、DSI_D1N,
DSI_CP、DSI_CN, Data Bus
TE、IC_ID
Tearing effect output
LCM ID
Grayscale
RST、MIPI_MODE Reset
Manipulation
Voltage
DC/DC
Mipi mode select
Power Supply
VDD, IOVDD
GND
18 GND
LCD Driver1C9hip (COG)
20
21 Back light
22 Figure 3.1 LCD module diagramLEDA.LEDK
24
25
26
27
28
Figure 4.4.1 LCD module diagram
The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation
and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of
TIANMA MICRO-ELECTRONICS Corporation.
Page 8 of 21
Vwhite: To be determined Vblack: To be determined.
Model No.TM040YDHG32
Note 4: Definition of Response time
The response time is defined as the LCD optical switching time interval between “White” state and
“Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90%
to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from 10%
to 90%.
Note 5: Definition of color chromaticity (CIE1931)
Color coordinates measured at center point of LCD.
Note 6: Definition of Luminance Uniformity
Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the
center of each measuring area.
Luminance Uniformity (U) = Lmin/ Lmax
L-------Active area length W----- Active area width
Lmax: The measured Maximum luminance of all measurement position.
Lmin: The measured Minimum luminance of all measurement position.
Note 7: Definition of Luminance:
Measure the luminance of white state at center point.
The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation
and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of
TIANMA MICRO-ELECTRONICS Corporation.
Page 16 of 21
|
|||
页数 | 21 页 | ||
下载 | [ TM040YDHG32.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
TM040YDHG32 | Display Module | Tianma |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |