|
|
零件编号 | V201V4-T02 | ||
描述 | TFT LCD Module | ||
制造商 | CHI MEI | ||
LOGO | |||
1 Page
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Jan. 03, 2006
Model No.: V201V4-T02
Approval
TFT LCD Approval Specification
MODEL NO.: V201V4 - T02
Customer:
Approved by:
Note:
AVP
QRA Dept.
Approval
ຫةԫ
LCD TV Head Division
ພၼ
DDIII
Approval
ޕޫ
TVHD / PDD
DDII
Approval
៴֮ᙘ
DDI
Approval
֮ࣥᜣ
LCD TV Marketing and Product Management Division
Product Manager
႓՛ဉ
1
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center
a. White Pattern
www.panelook.com
Issued Date: Jan. 03, 2006
Model No.: V201V4-T02
Approval
b. Black Pattern
Active Area
c. Vertical Stripe Pattern
Active Area
Active Area
RGB RGB
BRGB RGBR
BRGB RGBR
RGB RGB
8
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Jan. 03, 2006
Model No.: V201V4-T02
Approval
6.2 POWER ON/OFF SEQUENCE
To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the
diagram below.
Power Supply
VCC
0V
0ЉT1Љ10ms
0ЉT2Љ50ms
0ЉT3Љ50ms
5s ЉT4
Signals
0V
0.9 VCC
0.1VCC
T1
T2
Power On
VALID
0.9 VCC
0.1Vcc
T3
T4
Power Off
Backlight (Recommended)
100msЉT5
100msЉT6
50% 50%
T5 T6
Power ON/OFF Sequence
Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc.
Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance.
Note (4) T4 should be measured after the module has been fully discharged between power off and on period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.
16
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version2.0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
|
|||
页数 | 26 页 | ||
下载 | [ V201V4-T02.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
V201V4-T01 | TFT LCD Module | CHI MEI |
V201V4-T02 | TFT LCD Module | CHI MEI |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |