DataSheet8.cn


PDF ( 数据手册 , 数据表 ) HD-6150M3-AH

零件编号 HD-6150M3-AH
描述 3 dB 90 Card Couplers
制造商 Hirose Electric
LOGO Hirose Electric LOGO 


1 Page

No Preview Available !

HD-6150M3-AH 数据手册, 描述, 功能
3 dB 90° Card Couplers
HD-M Series
HD-0053M3-IH
HD-0195M3-DH
HD-0195M3-DH-1 HD-0900M3-CH-1
HD-0620M3-EH HD-1700M3-FH
HD-3900M3-BH
HD-0313M3-FH
HD-2100M3-CH
HD-1800M3-CH
HD-3200M3-BH
HD-6150M3-AH
sFeatures
1.High Performance
The high frequency characteristics feature.
Extremely low loss and a high degree of matching.
2.Power Uniform Distribution and
90° Phase Difference Type
This is a one input, two output (or two input, one
output) power uniform distribution type having a
90° phase difference between the two outputs (or
two inputs).
3.Miniature and Lightweight
Corrosion-resistant aluminum is used for the cover
and the Hirose Electric original pattern design,
which uses a stripline triplate method, enables the
couplers to be extremely small and lightweight.
4.Equipped with Tabs
Tabs permit direct mounting to surface circuits.
5.High Power Type
This type can be used with up to 100 W of power.
sProduct Specifications
Ratings
Frequency range (Note)
Characteristic impedance
Maximum Input Power (Note)
30 to 6400 MHz
50 ohms
50 to 100 W
Operating temperature range
Operating relative humidity
Note: The frequency range and the maximum input power will differ depending on the products.
-10ç to +65ç
95% Max.
Item
1.Insulation resistance 500M ohms min
Standard
2.Vibration
3.Shock
No electrical discontinuity of 1 µs or more
No damage, cracks, or parts dislocation
4.Temperature cycle No damage, cracks, or parts dislocation
5.Corrosion resistance No serious corrosion
6.Hydrogen sulfide gas No damage, cracks, or parts dislocation
qThe test method conforms to MIL-STD-202.
sMaterials
Conditions
100 V DC
Frequency of 10 to 2000 Hz, overall amplitude of 1.52 mm,
acceleration of 98 m/s2 for 2 hours in each of 3 directions
Acceleration of 980 m/s2, sine half-wave waveform,
3 cycles in each of the 3 axis
Temperature : -55ç ¡ +5ç to +35ç ¡ +85ç ¡ +5ç to +35ç
Time : 30 ¡ 15 max. ¡ 30 ¡ 15 max. (Minutes)
200 cycles
Exposed to 20% salt water solution for 48 hours
Exposed to 10% potassium sulfide solution for 100 hours
Part
Cover (A)
Cover (B)
Board
Rivets
Eyelet
Tabs
Cover (A)
Cover (B)
Material
Stainless steel
Aluminum
Dielectric
Aluminum
Brass
Phosphor bronze
Stainless steel
Stainless steel
Finish
---------
Conductive white Alumite
Gold plating
---------
Nickel plating
Gold plating
---------
---------
27







HD-6150M3-AH pdf, 数据表
sMounting Method
Fastening screw
Tab
Figure 1.
Microstrip board
Micro stripline
The three types of mounting methods
illustrated in the diagrams below will
mount the card coupler for use under
optimum conditions.
The fastening screws in the diagrams
are M2 screws tightened to 1.5 kg cm.
When the tip of the micro stripline is of
Teflon type material ( r = 2.6), C
chamfering of C1 is performed at t1.6,
and of C0.5 at t1.2.
The side view diagrams of Figure 1 are
illustrated in Figures 2, 3, and 4 below.
Gap S between the card coupler and
the microstrip board surface should be
used to agree with the following
conditions.
( Below 500 MHz ........S0.5 mm
500 to 2300 MHz......S0.25 mm
Above 2300 MHz......S0.15 mm
Metal plate or conductive spacer
Figure 2.
Figure 3.
Figure 4.
qWhen the Ground Board is Constructed of 0.4 mm Stainless and 0.8 mm Aluminum
(When the Thickness of the Microstrip Board is 1.6 or 1.2 mm)
For t1.6 boards, use with the stainless case of the card coupler facing upward. For t1.2 boards,
use with the aluminum case of the card coupler facing upward. Mount and fix the card coupler
with fastening screws as illustrated in Figure 2. Next, solder the tabs and micro stripline, then
use.
(When the Thickness of the Microstrip Board is Greater than 1.6 mm)
Insert a metal plate or a conductive spacer between the coupler and ground, then mount as
illustrated in Figure 3 so that the surface of the tabs and the position of the microstrip board are
equal. Fix the card coupler with fastening screws as illustrated in Figure 3. Next, solder the tabs
and micro stripline, then use.
(When the Thickness of the Microstrip Board is Less than 1.2 mm)
Cut the ground at the position of the coupler and attach so that the surface of the tabs is in
contact with the micro stripline. Fix the card coupler with fastening screws as illustrated in Figure
4. Next, solder the tabs and micro stripline, then use.
34














页数 9 页
下载[ HD-6150M3-AH.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
HD-6150M3-AH3 dB 90 Card CouplersHirose Electric
Hirose Electric

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap