|
|
零件编号 | A3150 | ||
描述 | PROGRAMMABLE/ CHOPPERSTABILIZED/ HALL-EFFECT SWITCH | ||
制造商 | Allegro MicroSystems | ||
LOGO | |||
1 Page
3150
PROGRAMMABLE, CHOPPER-
STABILIZED, HALL-EFFECT SWITCH
The A3150JLT and A3150JUA programmable switches provide
tooth/valley recognition in large gear-tooth sensing applications. Each
sensor consists of a single element, chopper-stabilized Hall-effect IC
that can be programmed to the desired magnetic switch point, opti-
mizing sensor airgap and timing accuracy performance after final
PTCT
packaging. The small package can be easily assembled and used in
V
TCC
UC .1 2
3
PRODE ONsLiYgnDwg.PH-003-2
ED NC dePRELIMINARY INFORMATION
U E(subject to change without notice)
IN R wApril 12, 1999
NT FE r neABSOLUTE MAXIMUM RATINGS
CO RE foat TA = 25°C
Supply Voltage, VCC ........................... 26.5 V
0Reverse Supply Voltage, VRCC ............ -30 V
IS R 5Overvoltage Supply Current, ICC ..... 100 mA
D O 2Magnetic Flux Density, B ............ Unlimited
F 3Output Current, IOUT ..... Internally Limited
Output OFF Voltage, VOUT ................. 26.5 V
AReverse Output Current, IROUT ......... -50 mA
— eOperating Temperature Range,
TA ............................... -40°C to +115°C
UsStorage Temperature, TS ................... +170°C
conjunction with a wide variety of gear/target shapes and sizes. The
two devices differ only in package style.
The sensing technology used for this sensor is Hall-effect based.
The sensor incorporates a single-element Hall IC that switches in
response to magnetic signals created by a ferrous target. The program-
mability of the circuit eliminates magnet and system offsets such as
those caused by tilt yet provides zero-speed detection capabilities
without the associated running jitter inherent in classical digital solu-
tions.
A proprietary dynamic offset cancelation technique, with an
internal high-frequency clock, reduces the residual offset voltage,
which is normally caused by device overmolding, temperature
dependancies, and thermal stress. This technique produces devices that
have an extremely stable quiescent output voltage, are immune to
mechanical stress, and have precise recoverability after temperature
cycling. Many problems normally associated with low-level analog
signals are minimized by having the Hall element and amplifier in a
single chip. Output precision is obtained by internal gain adjustments
during the manufacturing process and operate-point programming in the
user’s application.
This sensor system is ideal for use in gathering speed, position, and
timing information using gear-tooth-based configurations. The
A3150JLT/JUA are particularly suited to those applications that require
accurate duty cycle control or accurate edge detection. The lower
vibration sensitivity also makes these devices extremely useful for
transmission speed sensing.
Continued next page
Always order by complete part number: the prefix 'A' + the basic four-digit
part number + a suffix to indicate operating temperature range +
a suffix to indicate package style, e.g., A3150JLT .
3150
PROGRAMMABLE, CHOPPER-
STABILIZED, PRECISION,
HALL-EFFECT SWITCH
CRITERIA FOR DEVICE QUALIFICATION
All Allegro sensors are subjected to stringent qualification requirements prior to being released to production.
To become qualified, except for the destructive ESD tests, no failures are permitted.
Qualification Test
Test Method and Test Conditions
Biased Humidity (HAST) TA = 130°C, RH = 85%
High-Temperature
Operating Life (HTOL)
Accelerated HTOL
JESD22-A108,
TA = 150°C, TJ = 165°C
JESD22-A108,
TA = 175°C, TJ = 190°C
Autoclave, Unbiased
JESD22-A102, Condition C,
TA = 121°C, 15 psig
High-Temperature
(Bake) Storage Life
Temperature Cycle
MIL-STD-883, Method 1008,
TA = 170°C
MIL-STD-883, Method 1010,
-65°C to +150°C
Latch-Up
—
Electro-Thermally
Induced Gate Leakage
ESD,
Human Body Model
Electrical Distributions
—
CDF-AEC-Q100-002
Per Specification
Test Length Samples
50 hrs
77
408 hrs
77
504 hrs
77
96 hrs
77
1000 hrs
77
500 cycles
77
Pre/Post
Reading
Pre/Post
Reading
Pre/Post
Reading
—
6
6
x per
test
30
Comments
VCC = VOUT = 5 V
VCC = 24 V,
VOUT = 20 V
VCC = 24 V,
VOUT = 20 V
Test to failure,
All leads > TBD
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
|
|||
页数 | 12 页 | ||
下载 | [ A3150.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
A3150 | PROGRAMMABLE/ CHOPPERSTABILIZED/ HALL-EFFECT SWITCH | Allegro MicroSystems |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |