|
|
零件编号 | UC1701x | ||
描述 | HIGH-VOLTAGE MIXED-SIGNAL IC | ||
制造商 | UltraChip | ||
LOGO | |||
1 Page
HIGH-VOLTAGE MIXED-SIGNAL IC
65x132 STN Controller-Driver
MP Specifications
Revision 1.0
November 7, 2008
ULTRACHIP
The Coolest LCD Driver, Ever!
ULTRACHIP
High-Voltage Mixed-Signal IC
©1999~2008
Name
VDDX
TST4
TST2
Dummy
Type
I
I/O
Pins
4
1
1
11
Description
MISC. PINS
Auxiliary VDD. This pin is connected to the main VDD bus within the IC. It’s
provided to facilitate chip configurations in COG application.
There’s no need to connect VDDX to main VDD externally and it should NOT
be used to provide VDD power to the chip.
Test control. There’s an on-chip pull-up resistor for TST4. Leave it open
during normal use.
Test I/O pins. Leave these pins open during normal use.
Dummy pins are NOT connected inside the IC.
Note: Several control registers will specify “0 based index” for COM and SEG electrodes. In those
situations, COMX or SEGX will correspond to index X-1, and the value range for those index register will be
0~63 for COM and 0~131 for SEG.
8 MP Specifications
ULTRACHIP
High-Voltage Mixed-Signal IC
©1999~2008
17. Set LCD Bias Ratio
Action
C/D W/R D7 D6 D5 D4 D3 D2 D1 D0
Set Bias Ratio, BR
0 0 1 0 1 0 0 0 1 BR
Select voltage bias ratio required for LCD. Default : 0
The setting of Bias ratio varies according to Duty:
DUTY
1/65
1/49
1/33
1/55
BR = 0
1/9
1/8
1/6
1/8
BR = 1
1/7
1/6
1/5
1/6
18. Set Cursor Update Mode
Action
Set Cursor Update Mode
C/D W/R D7 D6 D5 D4 D3 D2 D1 D0
0011100000
This command is used for set cursor update mode function. When cursor update mode sets, UC1701x will
update register CR with the value of register CA. The column address CA will increment with write RAM
data operation but the address wraps around will be suspended no matter what WA setting is. However, the
column address will not increment in read RAM data operation. The set cursor update mode can be used to
implement “write after read RAM” function. The column address (CA) will be restored to the value, which is
before the set cursor update mode command, when reset cursor update mode.
The purpose of this pair commands and their feature is to support “write after read” function for cursor
implementation.
19. Reset Cursor Update Mode
Action
Reset Cursor Update Mode
Set AC3=0 and CA=CR.
C/D W/R D7 D6 D5 D4 D3 D2 D1 D0
0011101110
20. Set Static Indicator OFF
Action
Turn OFF Static Indicator
No Operation.
C/D W/R D7 D6 D5 D4 D3 D2 D1 D0
0010101100
21. Set Static Indicator ON
Action
Turn ON Static Indicator
No Operation.
C/D W/R D7 D6 D5 D4 D3 D2 D1 D0
0010101101
00- - - - - - - -
16 MP Specifications
|
|||
页数 | 48 页 | ||
下载 | [ UC1701x.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
UC1701x | HIGH-VOLTAGE MIXED-SIGNAL IC | UltraChip |
UC1701xGAA | HIGH-VOLTAGE MIXED-SIGNAL IC | UltraChip |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |