DataSheet8.cn


PDF ( 数据手册 , 数据表 ) MX25L25835E

零件编号 MX25L25835E
描述 FLASH MEMORY
制造商 MACRONIX
LOGO MACRONIX LOGO 


1 Page

No Preview Available !

MX25L25835E 数据手册, 描述, 功能
MX25L25835E
MX25L25835E
HIGH PERFORMANCE
SERIAL FLASH SPECIFICATION
P/N: PM1737
REV. 1.0, NOV. 29, 2011
1
http://www.Datasheet4U.com







MX25L25835E pdf, 数据表
555BLOCK DIAGRAM
HOLD#/SIO3
RESET#
CS#2
CS#1
SO/SIO1
MX25L25835E
HOLD#/SIO3
SCLK
RESET# 128Mb Flash SI/SIO0
memory
CS#2
SO/SIO1
GND
WP#/SIO2
HOLD#/SIO3
RESET#
128Mb Flash
memory
SCLK
SI/SIO0
CS#1
GND
SO/SIO1
WP#/SIO2
SCLK
SI/SIO0
GND
WP#/SIO2
P/N: PM1737
REV. 1.0, NOV. 29, 2011
8
http://www.Datasheet4U.com







MX25L25835E equivalent, schematic
MX25L25835E
Command
(byte)
1st byte
2nd byte
3rd byte
4th byte
Action
EXSO (exit
secured OTP)
C1 (hex)
to exit the 4K-
bit secured
OTP mode
RDSCUR
(read security
register)
WRSCUR
(write security
register)
SBLK (single
block lock
SBULK (single
block unlock)
RDBLOCK
(block protect
read)
2B (hex)
2F (hex)
36 (hex)
39 (hex)
3C (hex)
AD1 AD1 AD1
AD2 AD2 AD2
AD3 AD3 AD3
to read value to set the lock- individual block individual block read individual
of security down bit as (64K-byte) or (64K-byte) or block or sector
register "1" (once lock- sector (4K-byte) sector (4K-byte) write protect
down, cannot write protect unprotect
status
be update)
GBLK (gang
block lock)
7E (hex)
whole chip
write protect
COMMAND GBULK (gang
(byte)
block unlock)
1st byte
2nd byte
3rd byte
4th byte
Action
98 (hex)
whole chip
unprotect
NOP (No
Operation)
00 (hex)
RSTEN
(Reset Enable)
66 (hex)
RST (Reset
Memory)
99 (hex)
SBL (Set Burst
Length)
77 (hex)
Value
WPSEL
(Write Protect
Selection)
68 (hex)
ESRY (enable
SO to output
RY/BY#)
70 (hex)
to set Burst
length
to enter and to enable SO
enable individal to output RY/
block protect BY# during CP
mode
mode
COMMAND
(byte)
1st byte
2nd byte
3rd byte
4th byte
Action
DSRY (disable
SO to output
RY/BY#)
CLSR (Clear
SR Fail Flags)
80 (hex)
30 (hex)
to disable SO
to output RY/
BY# during CP
mode
clear security
register bit 6
and bit 5
Note 1: The count base is 4-bit for ADD(2) and Dummy(2) because of 2 x I/O. And the MSB is on SI/SIO1 which is different
from 1 x I/O condition.
Note 2: ADD=00H will output the manufacturer ID first and ADD=01H will output device ID first.
Note 3: It is not recommended to adopt any other code not in the command definition table, which will potentially enter the
hidden mode.
Note 4: RST command only executed if RSTEN command is executed first. Any intervening command will disable Reset.
P/N: PM1737
16
REV. 1.0, NOV. 29, 2011
http://www.Datasheet4U.com










页数 30 页
下载[ MX25L25835E.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
MX25L25835EFLASH MEMORYMACRONIX
MACRONIX

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap