DataSheet8.cn


PDF ( 数据手册 , 数据表 ) MAX4553

零件编号 MAX4553
描述 SPST Analog Switches
制造商 Maxim Integrated
LOGO Maxim Integrated LOGO 


1 Page

No Preview Available !

MAX4553 数据手册, 描述, 功能
19-1391; Rev 0; 10/98
±15kV ESD-Protected, Quad,
Low-Voltage, SPST Analog Switches
General Description
The MAX4551/MAX4552/MAX4553 are quad, low-volt-
age, single-pole/single-throw (SPST) analog switches.
Each switch is protected against ±15kV electrostatic
discharge (ESD) shocks, without latchup or damage.
On-resistance (100max) is matched between switch-
es to 4max, and is flat (8max) over the specified
signal range. Each switch can handle Rail-to-Rail® ana-
log signals. The off-leakage current is only 1nA at
+25°C and 10nA at +85°C.
The MAX4551 has four normally closed (NC) switches,
and the MAX4552 has four normally open (NO) switch-
es. The MAX4553 has two NC and two NO switches.
These CMOS switches can operate with dual power
supplies ranging from ±2V to ±6V or a single supply
between +2V and +12V. They are fully specified for sin-
gle +2.7V operation.
All digital inputs have +0.8V and +2.4V logic thresh-
olds, ensuring TTL/CMOS-logic compatibility when
using ±5V or a single +5V supply.
________________________Applications
Battery-Operated Equipment
Data Acquisition
Test Equipment
Avionics
Audio Signal Routing
Networking
____________________________Features
o ±15kV ESD Protection per IEC 1000-4-2
o +2V to +12V Single Supply
±2V to ±6V Dual Supplies
o 120Signal Paths with ±5V Supplies
o Low Power Consumption: <1µW
o 4 Separately Controlled SPST Switches
o Rail-to-Rail Signal Handling
o Pin-Compatible with Industry-Standard
DG211/DG212/DG213
o TTL/CMOS-Compatible Inputs with Dual ±5V or
Single +5V Supply
Ordering Information
PART
TEMP. RANGE PIN-PACKAGE
MAX4551CEE
0°C to +70°C
16 QSOP
MAX4551CSE
0°C to +70°C
16 Narrow SO
MAX4551CPE
0°C to +70°C
16 Plastic DIP
MAX4551C/D
0°C to +70°C
Dice*
MAX4551EEE
-40°C to +85°C
16 QSOP
MAX4551ESE
-40°C to +85°C
16 Narrow SO
MAX4551EPE
-40°C to +85°C
16 Plastic DIP
Ordering Information continued at end of data sheet.
*Contact factory for dice specifications.
Pin Configurations/Functional Diagrams/Truth Tables
TOP VIEW
IN1 1
COM1 2
NC1 3
V- 4
GND 5
NC4 6
COM4 7
IN4 8
MAX4551
16 IN2
15 COM2
14 NC2
13 V+
12 N.C.
11 NC3
10 COM3
9 IN3
QSOP/SO/DIP
MAX4551
LOGIC
SWITCH
0 ON
1 OFF
N.C. = NOT CONNECTED
IN1 1
COM1 2
NO1 3
V- 4
GND 5
MAX4552
16 IN2
15 COM2
14 NO2
13 V+
12 N.C.
NO4 6
COM4 7
11 NO3
10 COM3
IN4 8
9 IN3
QSOP/SO/DIP
MAX4552
LOGIC
SWITCH
0 OFF
1 ON
SWITCHES SHOWN FOR LOGIC "0" INPUT
IN1 1
COM1 2
NO1 3
V- 4
GND 5
NO4 6
COM4 7
MAX4553
16 IN2
15 COM2
14 NC2
13 V+
12 N.C.
11 NC3
10 COM3
IN4 8
9 IN3
QSOP/SO/DIP
LOGIC
MAX4553
SWITCHES
1, 4
SWITCHES
2, 3
0 OFF ON
1 ON OFF
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
________________________________________________________________ Maxim Integrated Products 1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
http://www.Datasheet4U.com







MAX4553 pdf, 数据表
±15kV ESD-Protected, Quad,
Low-Voltage, SPST Analog Switches
Applications Information
MAX4551/MAX4552/MAX4553
±15kV ESD Protection
The MAX4551/MAX4552/MAX4553 are ±15kV ESD-pro-
tected according to IEC 1000-4-2 at their NC/NO pins.
To accomplish this, bidirectional SCRs are included on-
chip between these pins and the GND pin. In normal
operation, these SCRs are off and have negligible
effect on the performance of the switches. When there
is an ESD strike at these pins, however, the voltages at
these pins go Beyond-the-Rails™ and cause the corre-
sponding SCR(s) to turn on in a few nanoseconds and
bypass the surge safely to ground. This method is
superior to using diode clamps to the supplies because
unless the supplies are very carefully decoupled
through low ESR capacitors, the ESD current through
the diode clamp could cause a significant spike in the
supplies. This may damage or compromise the reliabili-
ty of any other chip powered by those same supplies.
In the MAX4551/MAX4552/MAX4553, there are diodes
to the supplies in addition to the SCRs at the NC/NO
pins, but there is a resistance in series with these
diodes to limit the current into the supplies during an
ESD strike. The diodes are present to protect these
pins from overvoltages that are not as a result of ESD
strikes like those that may occur due to improper
power-supply sequencing.
Once the SCR turns on because of an ESD strike, it
continues to be on until the current through it falls
below its “holding current.” The holding current is typi-
cally 110mA in the positive direction (current flowing
into the NC/NO pin) and 95mA in the negative direction
at room temperature (see SCR Holding Current vs.
Temperature in the Typical Operating Characteristics).
The system should be designed such that any sources
connected to these pins are current limited to a value
below these to make sure the SCR turns off when the
ESD event gets over to resume normal operation. Also,
keep in mind that the holding current varies significant-
ly with temperature. At +85°C, which represents the
worst case, the holding currents drop to 70mA and
65mA in the positive and negative directions respec-
tively. Since these are typical numbers, to get guaran-
teed turn-off of the SCRs under all conditions, the
sources connected to these pins should be current lim-
ited to not more than half these values. When the SCR
is latched, the voltage across it is about ±3V, depend-
ing on the polarity of the pin current. The supply volt-
ages do not affect the holding currents appreciably.
The sources connected to the COM side of the switches
do not need to be current limited since the switches are
made to turn off internally when the corresponding
SCR(s) get latched.
Even though most of the ESD current flows to GND
through the SCRs, a small portion of it goes into the
supplies. Therefore, it is a good idea to bypass the
supply pins with 100nF capacitors directly to the
ground plane.
ESD protection can be tested in various ways. Trans-
mitter outputs and receiver inputs are characterized for
protection to the following:
• ±15kV using the Human Body Model
• ±8kV using the Contact Discharge method speci-
fied in IEC 1000-4-2 (formerly IEC 801-2)
• ±15kV using the Air-Gap Discharge method speci-
fied in IEC 1000-4-2 (formerly IEC 801-2).
ESD Test Conditions
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Human Body Model
Figure 8 shows the Human Body Model, and Figure 9
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the test device
through a 1.5kresistor.
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifi-
cally refer to integrated circuits. The MAX4551/MAX4552/
MAX4553 enable the design of equipment that meets
Level 4 (the highest level) of IEC 1000-4-2, without
additional ESD protection components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2. Because series resistance is
lower in the IEC 1000-4-2 ESD test model (Figure 10),
the ESD withstand voltage measured to this standard
is generally lower than that measured using the
Human Body Model. Figure 11 shows the current
waveform for the ±8kV IEC 1000-4-2 Level 4 ESD
Contact Discharge test.
The Air-Gap test involves approaching the device with
a charged probe. The Contact Discharge method
connects the probe to the device before the probe is
energized.
Beyond-the-Rails is a trademark of Maxim Integrated Products.
8 _______________________________________________________________________________________
http://www.Datasheet4U.com







MAX4553 equivalent, schematic
±15kV ESD-Protected, Quad,
Low-Voltage, SPST Analog Switches
Package Information (continued)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1998 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
http://www.Datasheet4U.com










页数 16 页
下载[ MAX4553.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
MAX455CMOS Video Multiplexer/AmplifierMaxim Integrated
Maxim Integrated
MAX4550Serially Controlled / Dual 4x2 / Clickless Audio/Video Analog Crosspoint SwitchesMaxim Integrated
Maxim Integrated
MAX4550-MAX4570Serially Controlled / Dual 4x2 / Clickless Audio/Video Analog Crosspoint SwitchesMaxim Integrated
Maxim Integrated
MAX4550CAISerially Controlled / Dual 4x2 / Clickless Audio/Video Analog Crosspoint SwitchesMaxim Integrated
Maxim Integrated

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap