DataSheet8.cn


PDF ( 数据手册 , 数据表 ) ZX-LD100L

零件编号 ZX-LD100L
描述 ZX Series Smart Sensors
制造商 Omron
LOGO Omron LOGO 


1 Page

No Preview Available !

ZX-LD100L 数据手册, 描述, 功能
Smart Sensors (Laser Type)
ZX Series (ZX-L-N)
Ordering Information
Sensors
Sensor Heads (Reflective)
Optical system
Diffuse reflective
Beam shape
Spot beam
Line beam
Regular reflective
Spot beam
Line beam
*1. For an average count of 4,096.
Sensing distance
40±10 mm
100±40 mm
300±200 mm
40±10 mm
100±40 mm
300±200 mm
30±2 mm
Resolution*1
2 µm
16 µm
300 µm
2 µm
16 µm
300 µm
0.25 µm
Model
ZX-LD40
ZX-LD100
ZX-LD300
ZX-LD40L
ZX-LD100L
ZX-LD300L
ZX-LD30V
ZX-LD30VL
Sensor Heads (Through-beam)
Optical system
Through-beam
Measuring width
1-mm dia.
5 mm
10 mm
30 mm
*1. For an average count of 64.
Sensing distance
0 to 2000 mm
0 to 500 mm
Resolution*1
4 µm
12 µm
Model
ZX-LT001
ZX-LT005
ZX-LT010
ZX-LT030
Amplifier Units
Appearance
Power supply
DC
NPN
Output type
Model
ZX-LDA11-N
PNP
ZX-LDA41-N
Note: Compatible connection with the Sensor Head.
.
ZX Series (ZX-L-N) Smart Sensors (Laser Type)
1
Free Datasheet http://www.Datasheet4U.com







ZX-LD100L pdf, 数据表
ZX-LD30V
Side-to-side Inclination
4
3
2 + inclination
inclination
1
White ceramic
SUS304
Black paper
0
−1
−2
−3
4
10 8 6 4 2 0 2 4 6 8 10
Angle of inclination (°)
Front-to-back Inclination
4
White ceramic
3 SUS304
Black paper
2 + inclination
inclination
1
0
1
2
3
4
10 8 6 4 2 0 2 4 6 8 10
Angle of inclination (°)
ZX-LD30VL
Side-to-side Inclination
4
3
2 + inclination
inclination
1
White ceramic
SUS304
Black paper
0
1
2
3
4
10 8 6 4 2 0 2 4 6 8 10
Angle of inclination (°)
Front-to-back Inclination
4 White ceramic
SUS304
3 Black paper
2
1
0
1
2
3 + inclination
4 inclination
10 8 6 4 2 0 2 4 6 8 10
Angle of inclination (°)
8 ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Free Datasheet http://www.Datasheet4U.com







ZX-LD100L equivalent, schematic
Precautions
Design Precautions
Ratings and Performance
• Conform to the specified ratings and performance. Refer to Speci-
fications for details.
1. Do not impose voltage exceeding the rated voltage, otherwise
the Sensor may be damaged.
2. When supplying power to the Sensor, make sure that the
polarity of the power is correct, otherwise, the Sensor may be
damaged. Do not connect to an AC power supply.
3. Do not short-circuit the load for the open collector output, oth-
erwise the Sensor may be damaged.
• Do not disconnect the connector connecting the Sensor Head and
the controller while power is being supplied, otherwise the Sensor
may be damaged.
• Allow a warm-up period of approximately 10 minutes after turning
ON the power supply.
• Objects of certain materials or shapes may not be detectable, or the
detection accuracy may not be sufficiently high. These include ma-
terials that are transparent or have extremely low reflectivity, and
objects that are smaller than the Sensor’s spot diameter or have ex-
treme curvature or inclination.
Power Supply and Wiring
• Prior to turning ON the power supply after wiring is completed,
check to make sure that the power supply is correct, that there are
no mistaken connections, e.g., connections that would short-circuit
the load, and that the load current is appropriate. Incorrect wiring
may result in damage to the Sensor or Unit.
• The total length of the Sensor cable or Amplifier cable must be 10 m
or less. Use an ZX-XC@A Extension Cable (order separately) if re-
quired to extend the cable from the Sensor. Use a shielded cable to
extend the Amplifier cable. The shielded cable must be the same as
that of the Amplifier cable.
• Do not lay a power supply cable for the ZX together with high-volt-
age lines or power lines to prevent interference, damage, and mal-
function.
• When using a commercially available switching regulator, ground
the FG (frame ground) terminal.
• If the power supply line is subject to surges, connect a surge ab-
sorber that meets the conditions of the usage environment.
• When using a Calculating Unit, connect the corresponding linear
ground of the Amplifier Unit.
Compatibility
• All Sensor Heads and Amplifier Units are compatible. Different Sen-
sor Heads may be purchased at a later date and used with existing
Amplifier Units.
Mutual Interference
• Two Sensor Heads can be used together, without danger of mutual
interference, by connecting the ZX-CAL 2 Calculating Unit between
two Amplifier Units.
Maintenance
• Always turn OFF the power supply before adjusting or removing the
Sensor Head.
• Cleaning
Do not use thinners, benzine, acetone, or kerosene for cleaning.
If dust or oil adheres to the filter on the front of the Sensor Head,
use the following procedure to clean.
1. Use a blower brush (used to clean camera lenses) to blow
large dust particles from the surface. Do not blow the dust
away with your mouth.
2. Use a soft cloth (for lenses) with a small amount of alcohol to
remove the remaining dust. Do not use a scrubbing action
when cleaning because scratches on the filter could result in
Sensor inaccuracy.
Other Precautions
Environment
1. Do not use the Sensor in strong electromagnetic fields or in an
environment where the operation of the Sensor is subject to
the reflection of intense light (such as other laser beams or
electric arc-welding machines.)
2. Do not operate the Sensor in the following locations:
• Locations subject to strong vibration.
• Locations subject to direct sunlight or near heating equip-
ment.
• Locations subject to high humidity.
• Locations where the Sensor would accumulate dust, dirt, me-
tallic powder, etc.
• Locations subject to corrosive or flammable gases.
• Locations subject to exposure to organic solvents, water, oil,
etc.
• Locations subject to strong electromagnetic or electrical
fields.
• Locations subject to rapid changes in temperature.
• Locations subject to freezing.
16 ZX Series (ZX-L-N) Smart Sensors (Laser Type)
Free Datasheet http://www.Datasheet4U.com










页数 28 页
下载[ ZX-LD100L.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
ZX-LD100ZX Series Smart SensorsOmron
Omron
ZX-LD100LZX Series Smart SensorsOmron
Omron

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap