DataSheet8.cn


PDF ( 数据手册 , 数据表 ) BF097XN02

零件编号 BF097XN02
描述 TFT LCD Module
制造商 InnoLux
LOGO InnoLux LOGO 


1 Page

No Preview Available !

BF097XN02 数据手册, 描述, 功能
PRODUCT SPECIFICATION
Doc. Number:
Tentative Specification
Preliminary Specification
Approval Specification
MODEL NO.: BF097XN01/02
Customer:
APPROVED BY
SIGNATURE
Note
Please return 1 copy for your confirmation with your
signature and comments.
Approved By
Checked By
Prepared By
Annie Lu
Version 0.0
3 May 2011
1 / 26
copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
The
Free Datasheet http://www.Datasheet4U.com







BF097XN02 pdf, 数据表
PRODUCT SPECIFICATION
4.3 ELECTRICAL CHARACTERISTICS
4.3.1 LCD ELECTRICAL SPECIFICATION
Parameter
Power Supply Voltage
Ripple Voltage
Inrush Current
Power Supply Current
Mosaic
White
Symbol
VCCS
VRP
IRUSH
lcc
Min.
3.0
-
-
-
-
Value
Typ.
3.3
50
-
227
297
Max.
Unit
Note
3.6 V
(1)
100 mV
(1)
1.5 A (1),(2)
250 mA
(3)a
327 mA
(3)b
Note (1) The ambient temperature is Ta = 25 ± 2 ºC.
Note (2) IRUSH: the maximum current when VCCS is rising
IIS: the maximum current of the first 100ms after power-on
Measurement Conditions: Shown as the following figure. Test pattern: white.
+3.3V
R1
47K
Q1 2SK1475
FUSE
VCCS
C3
(LCD Module Input)
1uF
(High to Low)
(Control Signal)
SW
+12V
C1
1uF
Q2
R2
2SK1470
1K
VR1
47K
C2
0.01uF
0.5ms
0V 10%
VCCS rising time is 0.5ms
+3.3V
90%
100ms
VCCS
I Rush
IIs
Icc
Version 0.0
3 May 2011
8 / 26
copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
The
Free Datasheet http://www.Datasheet4U.com







BF097XN02 equivalent, schematic
PRODUCT SPECIFICATION
Note (1): Measuring Conditions
The optical characteristics are determined after the unit has been ‘ON’ and stable at the maximum
brightness, in a dark environment at an ambient temperature at 25°C ± 2°C. The electrical conditions
include Vccs = 3.3 V, fv = 60 Hz, fCLK = 100 MHz, ILED = 20.0 mA . Recommended measuring equipments
for luminance and color is Photo Research PR650 Colorimeter or similar. The measuring distance should
be about 30-50 cm from the LCD surface at normal unless otherwise specified. The (virtual) measuring
spot should be 5mm in diameter. The CIE 1931 and 1967 Standards shall be used. Measurements should
be done on the 160 grid points as shown in the following figures. Viewing angle measurements should be
done by an Eldim EZ Color system or similar. Measurement data needs to be calibrated to Apple’s
equipment measurement results.
Note (2): Optical Measurement Set-up
Center Point Luminance
Lct = Average luminance at point # 72, 73, 88, 89 point of the display
Average Luminance
LAve = SUM (L1:L160) / 160 where L1 to L160 are the luminance values measured at point #1 to #160.
Version 0.0
3 May 2011
16 / 26
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited.
Free Datasheet http://www.Datasheet4U.com










页数 26 页
下载[ BF097XN02.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
BF097XN01TFT LCD ModuleInnoLux
InnoLux
BF097XN02TFT LCD ModuleInnoLux
InnoLux

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap