|
|
零件编号 | QD141X1LH06 | ||
描述 | Display Module | ||
制造商 | Quanta | ||
LOGO | |||
1 Page
These specification sheets are the proprietary product of Quanta Display Inc. (”QDI”)
and include materials protected under copyright of QDI. Do not reproduce or cause any third
party to reproduce them in any form or by any means, electronic or mechanical, for any
purpose, in whole or in part, without the express written permission of QDI.
The device listed in these technical literature sheets was designed and manufactured
for use in OA equipment.
In case of using the device for applications such as control and safety equipment for
transportation (aircraft, trains, automobiles, etc. ), rescue and security equipment and
various safety related equipment which require higher reliability and safety, take into
consideration that appropriate measures such as fail-safe functions and redundant system
design should be taken.
Do not use the device for equipment that requires an extreme level of reliability, such as
aerospace applications, telecommunication equipment (trunk lines), nuclear power control
equipment and medical or other equipment for life support.
QDI assumes no responsibility for any damage resulting from the use of the device
which does not comply with the instructions and the precautions specified in these
technical literature sheets.
Contact and consult with a QDI sales representative for any questions about this device.
Free Datasheet http://www.Datasheet4U.com
6. Electrical Characteristics
6-1.TFT-LCD panel driving
Parameter
Symbol Min.
Vcc Supply voltage
Current dissipation
Permissive input ripple
voltage
Differential input
High
threshold voltage Low
Input current (High)
Vcc
Icc
VRP
VTH
VTL
IOH
+3.0
–100
Input current (Low)
IOL
Terminal resistor
RT
Rush current
IRUSH
Note1 VCM : Common mode voltage
of LVDS driver.
Note2
On-off conditions for supply voltage
Typ.
+3.3
420
100
Max.
+3.6
TBD
100
Unit
mV p-p
Ta 25
Remark
Note2
Note3
Vcc=+3.3V
+100
10
10
1.5
mV VCM=+1.2V
mV Note1
A VI=2.4V
Vcc=3.6V
A VI=0V
Vcc=3.6V
Differential
input
A Rise time
470uS
0 t1 10 ms
0 t2 50 ms
0 t3 1 s
t4 1 s
Vcc-dip conditions
1) 2.5 V Vcc 3.0 V
td 10 ms
2) Vcc 2.5 V
Vcc-dip conditions should also follow the On-off conditions for supply voltage
Note3 Typical current situation : 16-gray-bar pattern.
Vcc=+3.3V
Free Datasheet http://www.Datasheet4U.com
Note1 Definitions of viewing angle range:
Note2 Definition of contrast ratio:
The contrast ratio is defined as the following.
Contrast Ratio (CR)=
Luminance (brightness) with all pixels white
Luminance (brightness) with all pixels black
Note3 Definition of response time:
The response time is defined as the following figure and shall be measured by
switching the input signal for "black" and "white" .
Note4 This shall be measured at center of the screen.
Note5 Definition of white uniformity:
White uniformity is defined as the
following with five measurements
(A E).
Maximum Luminance of five points (brightness)
Minimum Luminance of five points (brightness)
Free Datasheet http://www.Datasheet4U.com
|
|||
页数 | 18 页 | ||
下载 | [ QD141X1LH06.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
QD141X1LH03 | Laptop LCD Removal Instructions | L4L |
QD141X1LH06 | Display Module | Quanta |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |