|
|
零件编号 | SVA150XG10TB | ||
描述 | TFT LCD Module | ||
制造商 | NEC | ||
LOGO | |||
1 Page
www.DataSheet4U.com
4.3 ELECTRICAL CHARACTERISTICS
www.DataSheet4U.com
SN-SA-A0044-05E 8/31
4.3.1 Driving for LCD panel signal processing board
Parameter
Symbol
Power supply voltage
VCC
Power supply current
ICC
Permissible ripple voltage
VRP
Differential input threshold Low VTL
voltage for LVDS receiver
High VTH
Input voltage width for LVDS receiver
Vi
Terminating resistor
RT
Input voltage for MSL signal
Low
High
VFL
VFH
※1: Checkered flag pattern (EIAJ ED-2522);
※3: Common mode voltage for LVDS receiver
min. typ.
max. Unit
3.0 3.3
3.6 V
- (500)※1 (700)※2 mA
--
100 mV
-100 -
mV
--
100 mV
0-
2.4 V
- 100
-Ω
0-
0.8 V
2.0 -
VCC
V
※2: 2H1V dot inverse pattern
Remarks
-
at VCC = 3.3V
For VCC
at VCM = 1.2V
Note3
-
-
-
4.3.2 Driving for backlight lamp
Parameter
Symbol min. typ. max. Unit
Remarks
Lamp current
Il 3.5 7.0 7.5 mArms at L = 250cd/ m2 (typ.)
Lamp voltage
Vl 549 610 671 Vrms
For each lamp
Lamp starting voltage
Note1
VS
-
-
-
1600 Vrms
Ta = 0℃ Note2
- 1100 Vrms Ta = 25℃ Note2
Oscillation frequency FO 40 50 60 kHz
Note3
Note1: The value is the characteristic of lamp. The starting voltage of inverter should be lower than the value. But
the possibility of not lighting exists by the lower voltage, so the suitable voltage should considered by the
test .
Note2: The asymmetric ratio of working waveform for lamps (Lamp voltage peak ratio, Lamp current peak ratio
and waveform space ratio) should be less than 5% (See the following figure). If the waveform is asymmetric, DC
(Direct current) element applies into the lamp. In this case, a lamp lifetime may be shortened, because a
distribution of a lamp enclosure substance inclines toward one side between low voltage terminal (Cold terminal)
and high voltage terminal (Hot terminal).
Pa
Sa
Pb
Sb
|Pa - Pb| / Pb × 100 ≤ 5%
|Sa - Sb| / Sb × 100 ≤ 5%
Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative
Sa: Waveform space for positive part, Sb: Waveform space for negative part
Note3: Recommended value of “FO” is as following.
FO = 1/4 x 1/th x (2n-1) n: Natural number (1, 2, 3 ……)
Not duplication without authorization
Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
4.8.3 Input signal timing chart
tv
Tvd=768H
DE
DE
Thd=1024CLK
th
tc
DATA
Invalid
www.DataSheet4U.com
SN-SA-A0044-05E 16/31
Invalid
Not duplication without authorization
Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
|
|||
页数 | 30 页 | ||
下载 | [ SVA150XG10TB.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
SVA150XG10TB | TFT LCD Module | NEC |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |