DataSheet8.cn


PDF ( 数据手册 , 数据表 ) ZIC2410

零件编号 ZIC2410
描述 Single-chip 2.4GHz RF Transceiver
制造商 California Eastern Laboratories
LOGO California Eastern Laboratories LOGO 


1 Page

No Preview Available !

ZIC2410 数据手册, 描述, 功能
ZIC2410 Datasheetwww.DataSheet4U.com
APPLICATIONS
„ Home Automation and Security
„ Automatic Meter Reading
„ Factory Automation and Motor Control
„ Medical Patient Monitoring
„ Voice Applications
„ Replacement for legacy wired UART
„ Energy Management
„ Remote Keyless Entry w/
Acknowledgement
„ Toys
„ PC peripherals
KEY FEATURES
„ Embedded 8051 Compatible
Microprocessor with 96KB Embedded
Flash Memory for Program Space plus
8KB of Data Memory
„ Scalable Data Rate: 250kbps for ZigBee,
500kbps and 1Mbps for custom
applications.
„ Voice Codec Support:
µ-law/a-law/ADPCM
„ High RF RX Sensitivity: –98dBm @1.5V
„ High RF TX Power: +8dBm @1.5V
„ 4 Level Power Management Scheme
with Deep Sleep Mode (0.3µA)
„ Single Voltage operation: 1.9 to 3.3V
using an internal regulator (1.5V core)
„ Software Tools and Libraries for the
Development of Custom Applications
peripheral functions such as timers and UART
and is one of the first devices to provide an
embedded Voice CODEC. This chip is ideal for
very low power applications.
The ZIC2410 is available in two industry standard
packages: a 48-pin QFN (7x7mm) or a 72-pin
VFBGA (5x5mm) package.
CEL provides its customers with the CEL ZigBee
Stack, software in a compiled library, as well as all
the hardware & software tools required to develop
custom applications. User application software
can be compiled using any popular C-language
compiler such as Keil.
DESCRIPTION:
ZIC2410 is a true single-chip solution, compliant
with ZigBee specifications and IEEE802.15.4, a
complete wireless solution for all ZigBee
applications. The ZIC2410 consists of an RF
transceiver with baseband modem, a hardwired
MAC and an embedded 8051 microcontroller with
internal flash memory. The device provides
numerous general-purpose I/O pins,
Rev A







ZIC2410 pdf, 数据表
ZIC2410 Datasheet
(a) (b)
www.DataSheet4U.com
Upper 32KB
(0x10000~0x17FFF)
Upper 32KB
(0x10000~0x17FFF)
Mid 32KB
(0x08000~0x0FFFF)
Mid 32KB
(0x08000~0x0FFFF)
Low 32KB
(0x00000~0x07FFF)
Low 32KB
(0x00000~0x07FFF)
FBANK=0
FBANK=1
Figure 3 – Bank Selection of Program Memory
1.2.2 DATA MEMORY 
ZIC2410 reserves 64 KB of data memory address space. This address space can be accessed
by the MOVX command.
Figure 4 shows the address map of this data memory.
Rev A
Document No. 0005-05-07-00-000
Page 8 of 119







ZIC2410 equivalent, schematic
ZIC2410 Datasheet
www.DataSheet4U.com
Bit Name
Descriptions
R/W
Reset
Value
It controls the TX buffer function for each pin in Port3. When
7:0 P3OEN each bit field is set to ‘0’, the TX buffer of the corresponding pin R/W 0x00
outputs the value.
It controls the TX buffer function for each pin in Port1. When
6:0 P1OEN each bit field is set to ‘0’, the TX buffer of the corresponding pin R/W 0x00
outputs the value. P1.7 only acts as output.
It controls the TX buffer function for each pin in Port0. When
7:0 P0OEN each bit field is set to ‘0’, the TX buffer of the corresponding pin R/W 0x00
outputs the value.
P0REN/P1REN/P3REN (0xB9, 0xBA, 0xBC)
P0REN, P1REN, P3REN enable Pull-up of port 0, 1 and 3. When each bit area is cleared to ‘0’, the Pull-
up of the corresponding port is enabled.
7 Reserved
1
It controls the Pull-up function for each pin in Port3. When each
7:0 P3REN bit field is set to ‘0’, the Pull-up function of the corresponding pin R/W 0xFF
is operated.
It controls the Pull-up function for each pin in Port1. When each
bit field is set to ‘0’, the Pull-up function of the corresponding pin
6:0 P1REN is operated.
R/W 0x7F
*P1.7 doesn’t have a control field because it is operated as an
output.
It controls the Pull-up function for each pin in Port0. When each
7:0 P0REN bit field is set to ‘0’, the Pull-up function of the corresponding pin R/W 0xFF
is operated.
P0MSK (P0 INPUT MASK REGISTER, 0x84)
7:0
P0MSK
This register is used for masking the input of P0 pin (Refer to
P0AndSel in P0SEL register).
R/W 0xFF
P0SEL (P0 INPUT SELECTION REGISTER, 0x85)
7:2 Reserved
Controls the wake up of the MCU by an external interrupt when in
the power-down mode.
When this field is ‘0’, the MCU wakes up when INT0 or INT1
signal is high (This is the normal case in the MCU.)
1 ExNoEdge When this field is ‘1’, the MCU is woken up by the wakeup signal
of the SleepTimer. Remote control function can be implemented
by the interrupt service routine of the MCU when the WAKEUP
signal occurs by adjusting the RTDLY value in the Sleep Timer
while either INT0 or INT1 is low.
When this field is set to ‘1’, P0 and P0MSK are ORed per bit. The
0 P0AndSel bits of the result value are to be ANed and then output to P1.7.
This function is used to implement remote control function.
R/W
R/W
0
0
0
Rev A
Document No. 0005-05-07-00-000
Page 16 of 119










页数 70 页
下载[ ZIC2410.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
ZIC2410Single-chip 2.4GHz RF TransceiverCalifornia Eastern Laboratories
California Eastern Laboratories

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap