DataSheet8.cn


PDF ( 数据手册 , 数据表 ) ED-205

零件编号 ED-205
描述 AV Surround Processor
制造商 Onkyo
LOGO Onkyo LOGO 


1 Page

No Preview Available !

ED-205 数据手册, 描述, 功能
AV Surround Processor
ED-205
Instruction Manual
AV SURROUND PROCESSOR
STANDBY/ON
STANDBY
POWER
ON OFF
EFFECT
MODE
MASTER VOLUME
MULTICHINPUT LINE VIDEO-1/2
ED-205
Thank you for purchasing the ONKYO AV Surround
Processor.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable you
to obtain optimum performance and listening enjoyment
from your new AV Surround Processor.
Please retain this manual for future reference.
www.DataSheet4U.com
Contents
Before using
Important Safeguards ........................... 2
Precautions ........................................... 3
Features ................................................ 4
Supplied accessories ............................ 4
Before using this unit ........................... 5
Preparation
Connecting the amplifier and video
equipment ........................................... 6
Connecting equipment with 5.1-
channel audio output .......................... 7
Speaker placement and connection ...... 8
Connecting the z remote control
cables................................................ 10
Connecting the power ........................ 10
Operation
Using the remote controller ............... 11
Using the Surround modes ................. 12
Playing a source ................................. 14
A few important notes
Troubleshooting ................................. 17
Control positions and names .............. 18
Specifications ..................................... 20







ED-205 pdf, 数据表
Speaker placement and connection
www.DataSheet
The unit is equipped with speaker terminals for connecting the
Center speaker and Surround speakers, in addition to the
SUBWOOFER PRE OUT jack to allow connection to your
Subwoofer.
Use the ED-205's SUBWOOFER PRE OUT jack to connect
your Subwoofer, even if your amplifier also has a subwoofer
connection jack.
Connect the Left and Right front speakers to your amplifier's
speaker terminals.
Speaker placement
TV/Screen
Left Front Sub- Center
speaker woofer speaker
Right Front
speaker
Left
Surround
speaker
Listening
position
Right
Surround
speaker
In this section, only one example of possible speaker placement
is shown. Note, however, that ideal speaker placement varies
depending on the size of the room and the wall coverings used
in the room. To obtain ideal sound field effects, the Left and
Right front speakers must be placed at equal distances from the
listening position.
Important Points
• Left and Right front speakers (L/R) and Center
speaker (C)
Place these three speakers at the same height from the floor.
Place each speaker so that sound is aimed at the audience's
ears at the listening position.
• Left and Right Surround speakers (LS/RS)
Place these speakers so that their height is 1 meter (3 feet)
higher than that of the audience's ears.
• Subwoofer (SW)
Place it anywhere in your listening room that produces
satisfactory sound. The placement of the Subwoofer affects
the perceived direction of the sound very little, but optimal
bass reproduction will be achieved with placement in a
corner.
If your speaker system lacks Subwoofer, Center
speaker, or Surround speakers
To get the highest-quality surround sound from the ED-205, you
need a complete set of 6 speakers. However, you can enjoy
quality surround sound by setting the ED-205 to properly
distribute the sound originally intended for these non-existing
speakers to existing front and surround speakers, even if your
system lacks the subwoofer, center speaker, or surround
speakers.
1
15mm
2
3 45
Notes:
8
Connecting the speaker cables
1 Peel the insulation off the ends of the speaker cable 15 mm.
Do not cut core wires.
2 Twist the core wires.
3 Press the lever below the speaker terminal to open the
connection hole.
4 Insert the core wires into connection hole.
5 Return the lever to the original position.Make sure that the
core wires are barely visible where they enter the connection
hole.
Notes:
• Be sure to connect the Right and Left speakers to the unit's
corresponding speaker terminals. Also, be sure that you are
connecting the speaker's positive (+) and negative (-) binding
posts with unit's corresponding speaker terminals. Otherwise,
inferior sound will result.
• Use speakers whose nominal impedance is 6 to 16Ω.
Connecting a speaker whose impedance is lower than 6may
cause damage to the unit.
• Do not connect two or more speaker cables to the same
speaker terminal. Doing so may cause damage to the unit.
• To prevent damage to the circuitry, never short-circuit the
positive (+) and negative (-) speaker wires by allowing them
to touch each other.







ED-205 equivalent, schematic
Playing a source
www.DataSheet4U.com
1
AV SURROUND PROCESSOR
STANDBY/ON
STANDBY
POWER
ON OFF
4
EFFECT
MODE
MASTER VOLUME
MULTICHINPUT LINE VIDEO-1/2
ED-205
2
1 POWER SLEEP LINE-1 LINE-2
TUNER
PRESET
FM
AM
DVD
MD
TAPE
DISC
CD
EFFECT MULTI CH LINE VIDEO
2
MODE CH SEL
LEVEL
512
DELAY
TIME
TEST
TONE
VOLUME
CENTER
MODE MUTING
4
RC-394S
REMOTE CONTROLLER
(Front panel)
1 STANDBY/ON
(Remote controller)
POWER
2 MULTI CH INPUT
MULTI CH
4 MASTER VOLUME
VOLUME
51
2
16
CH SEL
LEVEL
CH SEL
LEVEL
Playing a multi-channel input source
The following describes how to play a multi-channel input
source. A multi channel input source refers to equipment with
5.1-channel output jacks (such as a DVD player). When
connected to the ED-205, the equipment outputs separate signals
to the 5 speaker channels (Left/Right front, Center, and Left/
Right Surround). The ED-205 then outputs the signal for the
subwoofer channel to its SUBWOOFER PRE OUT jack. In the
Multi-channel input mode, you cannot use the surround modes.
For how to connect a multi-channel input source, see page 7.
Before playing a multi-channel input source
• The ED-205 stores the output level you set for each speaker
connected to the MULTI CHANNEL INPUT jack. This stored
setting has no effect on the DOLBY PRO LOGIC output levels
you set using- the test tone.
1. Press the POWER button.
The STANDBY indicator goes out and the display lights up.
2. Press the MULTI-CH INPUT button.
3. Play the input source connected to the MULTI CHANNEL
INPUT jacks.
4. Adjust the sound volume.
The sound volume for all speakers simultaneously changes.
Adjust the sound volume from the listening position using the
remote controller.
5. Adjust the output level of each speaker according to your
taste.
The output levels for the Center speaker (CENTER), Right
Surround speaker (R-SUR), Left Surround speaker (L-SUR),
and Subwoofer (SW) can be adjusted.
1 Select the speaker channel to adjust by using the CH
SEL button on the remote controller.
2 Adjust the output level using the LEVEL y/u
buttons.
The adjustment range for the Center, and Left/Right Surround
speakers is -12dB to +12dB. For the Subwoofer, it is -30 to
+12dB.










页数 20 页
下载[ ED-205.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
ED-205AV Surround ProcessorOnkyo
Onkyo

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap