DataSheet8.cn


PDF ( 数据手册 , 数据表 ) ACE24C64

零件编号 ACE24C64
描述 Two-wire Serial EEPROM
制造商 ACE Technology
LOGO ACE Technology LOGO 


1 Page

No Preview Available !

ACE24C64 数据手册, 描述, 功能
 
www.DataSheet4U.com
ACE24C32/64                                                                                                                                                           
                                              Technology
Two-wire Serial EEPROM
Description
The ACE24C32/64 provides 32,768/65,536 bits of serial electrically erasable and programmable read-only
memory (EEPROM) organized as 4096/8192 words of 8 bits each. The device’s cascadable feature allows up to
8 devices to share a common two-wire bus. The device is optimized for use in many industrial and
commercial applications where low-power and low-voltage operations are essential.
Features
z Low Operation Voltage: Vcc = 1.7V to 5.5V
z Internally Organized: 4096 x 8,8192 x 8
z Two-wire Serial Interface
z Schmitt Trigger, Filtered Inputs for Noise Suppression
z Bi-directional Data Transfer Protocol
z 1MHz (2.5V~5.5V) and 400 kHz (1.7V) Compatibility
z Write Protect Pin for Hardware Data Protection
z 32-byte Page Write Modes (Partial Page Writes are Allowed)
z Self-timed Write Cycle (5 ms max)
z High-reliability - Endurance: 1,000,000 Write Cycles
- Data Retention: 100 Years
z TDFN ROHS compliant Packages
z Wafer Sales: available in inked wafer Form
Absolute Maximum Ratings
Operating Temperature
Storage Temperature
-55to +125
-65to +150
Voltage on Any Pin with Respect to Ground -1.0V to +7.0V
Maximum Operating Voltage
6.25V
DC Output Current
5.0 mA
*Notice: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational
sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Packaging Type
TDFN
VER 1.3 1 







ACE24C64 pdf, 数据表
 
www.DataSheet4U.com
ACE24C32/64                                                                                                                                                           
                                              Technology
Two-wire Serial EEPROM
Device Addressing
The 32K, 64K EEPROM devices all require an 8-bit device address word following a start condition to
enable the chip for a read or write operation (refer to Figure 7).
The device address word consists of a mandatory one, zero sequence for the first four most
significant bits as shown. This is common to all the EEPROM devices.
The 32/64K EEPROM use the three device address bits A2, A1, A0 to allow as many as eight devices
on the same bus. These bits must compare to their corresponding hard-wired input pins. The A2,A1 and
A0 pins use an internal proprietary circuit that biases them to a logic low condition if the pins are
allowed to float.
The eight bit of the device address is the read/write operation select bit. A read operation is initiated if
this bit is high and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the
device will return to a standby state.
Noise protection:
Special internal circuitry place on the SDA and SCL pins prevent small noise spikes from activating the
device.
Date Security:
The ACE24C32/64 has a hardware data protection scheme that allows the user to write protect the
entire memory when the WP pin is at Vcc.
Write Operations
Byte Write:
A write operation requires two 8-bit data word address following the device address word and
acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then
clock in the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a
zero and the addressing device, such as a microcontroller, must terminate the write sequence with a
stop condition. At this time the EEPROM enters an internally timed write cycle, tWR, to the nonvolatile
memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write
is complete (refer to Figure 8).
Page Write:
The 32K/64K EEPROM is capable of an 32-byte page write.A page write is initiated the same as a
byte write, but the microcontroller does not send a stop condition after the first data word is clocked in.
Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can
transmit up to 31 more data words. The EEPROM will respond with a zero after each data word received.
The microcontroller must terminate the page write sequence with a stop condition (refer to Figure 9).
The data word address lower five bits are internally incremented following the receipt of each data word.
The higher data word address bits are not incremented, retaining the memory page row location. When
the word address, internally generated, reaches the page boundary, the following byte is placed at the
beginning of the same page. If more than 32 data words are transmitted to the EEPROM, the data
word address will “roll over” and previous data will be overwritten.
VER 1.3 8














页数 13 页
下载[ ACE24C64.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
ACE24C64Two-wire Serial EEPROMACE Technology
ACE Technology

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap