DataSheet8.cn


PDF ( 数据手册 , 数据表 ) 6ES72xxxxxx

零件编号 6ES72xxxxxx
描述 Programmable Controller System Manual
制造商 ETC
LOGO ETC LOGO 


1 Page

No Preview Available !

6ES72xxxxxx 数据手册, 描述, 功能
Technical Specifications
In This Chapter
www.DataSheet4U.com
General Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Expansion Modules Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Expansion Modules Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermocouple and RTD Expansion Modules Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EM 277 PROFIBUS--DP Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EM 241 Modem Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EM 253 Position Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(CP 243--1) Ethernet Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(CP 243--1 IT) Internet Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(CP 243--2) AS--Interface Module Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Expansion Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RS-232/PPI Multi-Master Cable and USB/PPI Multi-Master Cable . . . . . . . . . . . . . . . . . . . . . .
Input Simulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
392
395
404
411
423
435
447
449
455
457
460
462
463
464
468
391







6ES72xxxxxx pdf, 数据表
S7-200 Programmable Controller System Manual
Table A-7 CPU Digital Output Specifications
General
Type
Rated voltage
Voltage range
Surge current (max.)
www.DataSheet4U.com Logic 1 (min.)
Logic 0 (max.)
Rated current per point (max.)
Rated current per common (max.)
Leakage current (max.)
Lamp load (max.)
Inductive clamp voltage
On State resistance (contact)
Isolation
Optical (galvanic, field to logic)
Logic to contact
Resistance (logic to contact)
Isolation groups
Delay (max.)
Off to on (µs)
On to off (µs)
Switching
Pulse frequency (max.)
Lifetime mechanical cycles
Lifetime contacts
Outputs on simultaneously
Connecting two outputs in parallel
Cable length (max.)
Shielded
Unshielded
24 VDC Output
(CPU 221, CPU 222,
CPU 224, CPU 226)
Solid State-MOSFET (Sourcing)
24 VDC Output
(CPU 224XP)
24 VDC
20.4 to 28.8 VDC
8 A for 100 ms
24 VDC
5 to 28.8 VDC (Q0.0 to
Q0.4)
20.4 to 28.8 VDC (Q0.5 to
Q1.1)
24 VDC Output
(CPU 224XPsi)
Solid State-MOSFET
(Sinking)
24 VDC
5 to 28.8 VDC
20 VDC at maximum
current
L+ minus 0.4 V at max.
current
0.1 VDC with 10 K Load
0.75 A
6 A 3.75 A
10 µ A
5W
L+ minus 48 VDC, 1 W dissipation
0.3 typical (0.6 Ω max.)
External Voltage Rail
minus 0.4V with 10K
pullup to External Voltage
Rail
1M + 0.4V at max. load
7.5 A
1M +48 VDC, 1 W
dissipation
500 VAC for 1 minute
--
--
See wiring diagram
2µs (Q0.0, Q0.1),
15µs (all other)
10µs (Q0.0, Q0.1), 130µs
(all other)
--
0.5µs (Q0.0, Q0.1), 15µs (all other)
1.5µs (Q0.0, Q0.1), 130µs (all other)
--
20 kHz1 (Q0.0 and Q0.1) 100 kHz1 (Q0.0 and Q0.1) 100 kHz1 (Q0.0 and Q0.1)
-- -- --
-- -- --
All at 55° C (horizontal), All at 45° C (vertical)
Yes, only outputs in same group
500 m
150 m
Relay Output
Dry contact
24 VDC or 250 VAC
5 to 30 VDC or 5 to 250
VAC
5 A for 4 s @ 10% duty
cycle
--
--
2.0 A
10 A
--
30 W DC; 200 W AC2, 3
--
0.2 (max. when new)
--
1500 VAC for 1 minute
100 M
See wiring diagram
--
--
10 ms
1 Hz
10,000,000 (no load)
100,000 (rated load)
No
1 Depending on your pulse receiver and cable, an additional external load resistor (at least 10% of rated current) may improve pulse signal quality and noise
immunity.
2 Relay lifetime with a lamp load will be reduced by 75% unless steps are taken to reduce the turn-on surge below the surge current rating of the output.
3 Lamp load wattage rating is for rated voltage. Reduce the wattage rating proportionally for voltage being switched (for example 120 VAC -- 100 W).
Warning
When a mechanical contact turns on output power to the S7-200 CPU, or any digital expansion module, it
sends a “1” signal to the digital outputs for approximately 50 microseconds.
This could cause unexpected machine or process operation which could result in death or serious injury to
personnel, and/or damage to equipment.
You must plan for this, especially if you are using devices which respond to short duration pulses.
398







6ES72xxxxxx equivalent, schematic
S7-200 Programmable Controller System Manual
Table A-14 Digital Expansion Modules Output Specifications
General
24 VDC Output
0.75 A
5A
Relay Output
2A
10 A
120/230 VAC Output
Type
Solid state-MOSFET (Sourcing)
Dry contact
Triac, zero-cross turn-on
Rated voltage
24 VDC
24 VDC or 250 VAC
120/230 VAC
Voltage range
20.4 to 28.8 VDC
5 to 30 VDC or
5 to 250 VAC
12 to 30 VDC or
12 to 250 VAC
40 to 264 VAC
(47 to 63 Hz)
24 VDC coil power voltage range
--
20.4 to 28.8 VDC
--
Surge current (max.)
8 A for 100 ms 30 A
5 A for 4 s @ 10%
duty cycle
15 A for 4 s @
10% duty cycle
5 A rms for 2 AC cycles
Logic 1 (min.)
www.DataSheet4U.com Logic 0 (max.)
Rated current per point (max.)
20 VDC
0.1 VDC with
10 K Load
0.75 A
0.2 VDC with 5 K
Load
5A
--
--
2.00 A
L1 (--0.9 V rms)
--
10 A resistive;
2 A DC inductive;
3 A AC inductive
0.5 A AC1
Rated current per common (max.)
10 A
5A
10 A
10 A
0.5 A AC
Leakage current (max.)
10 µA
30 µA
--
1.1 mA rms at 132 VAC
and 1.8 mA rrms at 264
VAC
Lamp load (max.)
Inductive clamp voltage
5W
L+ minus 48 V
50 W
L+ minus 47 V2
30 W DC/
200 W AC4,5
--
100 W DC/
1000 W AC
60 W
--
On state resistance (contact)
0.3 typical
(0.6 max.)
0.05 max.
0.2 max. when new 0.1 max.
when new
410 max. when load
current is less than
0.05A
Isolation
Optical (galvanic, field to logic)
Coil to logic
Coil to contact
Resistance (coil to contact)
Isolation groups
500 VAC for 1 minute
--
--
--
See wiring diagram
--
None
1500 VAC for 1 minute
100 M min. when new
See wiring diagram
1500 VAC for 1minute
--
--
--
1 point
Delay Off to On/On to Off (max.)
Switching (max.)
50 µs / 200 µs
--
500 µs
--
--
10 ms
--
15 ms
0.2 ms + 1/2 AC cycle
--
Switching frequency (max.)
--
1 Hz
10 Hz
Lifetime mechanical cycles
--
10,000,000 (no load)
30,000,000
(no load)
--
Lifetime contacts
--
100,000 (rated load)
30,000
(rated load)
--
Output on simultaneously
All at 55° C (horizontal), All at 45° C (vertical)
All at 55 °C
(horizontal) with
20A max. module
current. All at
45°C (vertical) with
20A max. module
current5. All at 40
°C (horizontal) with
10A per point
All at 55° C (horizontal),
All at 45° C (vertical)
Connecting two outputs in parallel
Yes, only outputs in same group
No
No
Cable length (max.)
Shielded
Unshielded
500 m
150 m
500 m
150 m
500 m
150 m
1 Load current must be full wave AC and must not be half-wave because of the zero-cross circuitry. Minimum load current is 0.05 A AC. With a load current
between 5 mA and 50 mA AC, the current can be controlled, but there is an additional voltage drop due to series resistance of 410 Ohms.
2 If the output overheats due to excessive inductive switching or abnormal conditions, the output point may turn off or be damaged. The output could overheat
or be damaged if the output is subjected to more than 0.7 J of energy switching an inductive load off. To eliminate the need for this limitation, a suppression
circuit as described in Chapter 3 can be added in parallel with the load. These components need to be sized properly for the given application.
3 The EM 222 DO 4 x Relay has a different FM rating than the rest of the S7-200. This module has a T4 rating, instead of T4A for FM Class I, Division Groups
A, B, C, and D Hazardous Locations.
4 Relay lifetime with a lamp load will be reduced by 75% unless steps are taken to reduce the turn-on surge below the surge current rating of the output.
5 Lamp load wattage rating is for rated voltage. Reduce the wattage rating proportionally for voltage being switched (for example 120 VAC -- 100 W).
Warning
When a mechanical contact turns on output power to the S7-200 CPU, or any digital expansion module, it
sends a “1” signal to the digital outputs for approximately 50 microseconds.
This could cause unexpected machine or process operation which could result in death or serious injury to
personnel, and/or damage to equipment.
You must plan for this, especially if you are using devices which respond to short duration pulses.
406










页数 30 页
下载[ 6ES72xxxxxx.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
6ES72xxxxxxCentral Processing UnitsSiemens
Siemens
6ES72xxxxxxProgrammable Controller System ManualETC
ETC

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap