DataSheet8.cn


PDF ( 数据手册 , 数据表 ) EE-SX47

零件编号 EE-SX47
描述 (EE-SX47 / EE-SX67) Photomicrosensor
制造商 OMRON
LOGO OMRON LOGO 


1 Page

No Preview Available !

EE-SX47 数据手册, 描述, 功能
www.DataSheet4U.com
Photomicrosensor
Back
EE-SX67/47
Photomicrosensor with 50- to 100-mA
Switching Capacity that can be Built
into Equipment
PNP output models newly added.
Standard, L-shaped, T-shaped, and Close-mount-
ing: Five series of models available.
Select from thirty output variations, including
Light-ON or Dark-ON/Light-ON (selectable) mod-
els.
Response frequency as high as 1 kHz.
Easy operation monitoring with bright light
indicator.
Wide operating voltage range from 5 to 24 VDC.
Models (EE-SXjjjA and EE-SXjjjR) with
operation indicators that are lit when sensing
objects are detected (when light is interrupted) are
available.
Ordering Information
Appearance
Standard
Sensing method
Through-beam
type (slot type)
Sensing
distance
5 mm
(slot width)
Output configuration
Dark-ON/Light-ON
(selectable) *1
NPN
EE-SX670
EE-SX670A*2
Model
PNP
EE-SX670P
EE-SX670R*3
Weight
Approx. 3.1 g
L-shaped
T-shaped
Light-ON
Dark-ON/Light-ON
(selectable) *1
Light-ON
Dark-ON/Light-ON
(selectable) *1
EE-SX470
EE-SX671
EE-SX671A*2
EE-SX471
EE-SX672
EE-SX672A*2
EE-SX470P
EE-SX671P
EE-SX671R*3
EE-SX471P
EE-SX672P
EE-SX672R*3
Approx. 3.0 g
Approx. 2.4 g
Close-mounting
Light-ON
Dark-ON/Light-ON
(selectable) *1
EE-SX472
EE-SX673
EE-SX673A*2
EE-SX472P
EE-SX673P
EE-SX673R*3
Approx. 2.3 g
Light-ON
EE-SX473
EE-SX473P
Close-mounting
Dark-ON/Light-ON
(selectable) *1
EE-SX674
EE-SX674A*2
EE-SX674P
EE-SX674R*3
Approx. 3.0 g
Light-ON
EE-SX474
EE-SX474P
Note:
*1. The Dark-ON/Light-ON (selectable) models can be used as Light-ON models when the L terminal and positive (+) terminal are
short-circuited. An L terminal and positive (+) terminal short-circuit connector (EE-1001-1) is available.
*2. Models with a suffix “A,” such as EE-SX670A, have a Dark-ON indicator that is lit when light is interrupted.
*3. Models with a suffix “R,” such as EE-SX670R, have a Dark-ON indicator that is lit when light is interrupted.
1







EE-SX47 pdf, 数据表
EE-SX67/47
EE-SX67/47
Precautions
Do not use the EE-SX at voltage exceeding the rated voltage range,
otherwise the EE-SX may be damaged.
+
Out
Sensor
Load
If the load is a relay or other small inductive load, connect the load to
the EE-SX as shown below. Be sure to connect a diode for counter-
voltage absorption.
OUT
Relay
Do not make mistakes in wiring, such as mistakes in polarity, other-
wise the EE-SX may be damaged.
+
Out
Sensor
Load
Do not short-circuit the load (i.e., do not connect a power supply di-
rectly to the Sensor) as shown below, otherwise the EE-SX may be
damaged.
+
Sensor Out
Load
Load
short-circuiting
! Caution
Mounting
The EE-SX is a Sensor to be built into equipment. Therefore, no
special protective measures have been taken to protect the EE-SX
from external light disturbance. Make sure that the EE-SX is not
affected by incandescent lamps or other light sources that may
cause external light disturbance, otherwise the EE-SX may mal-
function.
Be sure to mount the Sensor securely to flat plates. The characteris-
tics of the Through-beam Sensor change if the slot is deformed.
Use M3.0 screws when mounting the EE-SX. Be sure to use spring
washers with the screws so that the screws will not loosen. The
tightening torque applied to each screw must be no more than
0.59 N S m (6 kgf S cm).
Make sure that nothing will come into contact with the sensing ele-
ment of the Sensor. If the sensing element has scratch damage, the
characteristics of the Sensor will decrease.
Make sure that the EE-SX is securely mounted and not loosened by
vibration or shock.
Wiring
Countermeasures Against Surge
If the power supply has surge voltage, connect a Zener diode with-
standing 30 to 35 V or 0.1 to 1-µF capacitor in parallel to the power
supply to absorb the surge voltage.
0.1 to 1 µF
Do not wire power lines or high-tension lines alongside the lines of
the EE-SX in the same conduit, otherwise the EE-SX may be dam-
aged or malfunction due to induction. Be sure to wire the lines of the
EE-SX separately from power lines or high-tension lines or lay them
in an exclusive, shielded conduit.
Voltage Output
A Sensor with open collector output can be connected to a device
with voltage-input specifications by connecting a resistor between
the power supply and output terminals as shown in the following cir-
cuit diagram. The resistance of the resistor is normally 4.7 kand
must withstand a power of 0.5 W at 24 V and 0.25 W at 12 V.
EE-SX67/47 NPN models
Counter (voltage-input model)
Resistor
+24 V (power supply)
Sensor
main
circuit
Output
Input terminal (CP)
Input impedance:
approx. 4.7 k
EE-SX47/67 NPN Models with a 4.7-kResistor
High level:
Input voltage (VH) =
Z
R+Z
VCC =
4.7 k
4.7 k + 4.7 k
x 24 V = 12 V
Low level:
Input voltage (VL) x 0.4 V
VCC
Load current (IC) = R
=
24 V = 5.1 mA x 50 to 100 mA
R
EE-SX67/47 PNP models
Sensor
main
circuit
Resistor
Output
+24 V (power supply)
Input terminal (CP)
Input impedance:
approx. 4.7 k
EE-SX47/67 PNP Models with a 4.7-kResistor
High level:
Input voltage (VH) = Vcc–residual voltage
[24 V–1.3 V=22.7 V
Low level:
Input voltage (VL) [0 V
Note: Refer to the ratings of the Sensor for the relationship be-
tween the residual voltage and load current.
8














页数 12 页
下载[ EE-SX47.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
EE-SX4009-P10Photomicrosensor (Transmissive)Omron Electronics
Omron Electronics
EE-SX405PhotomicrosensorOmron
Omron
EE-SX4070PhotomicrosensorOmron
Omron
EE-SX4088-W11PhotomicrosensorOmron
Omron

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap