DataSheet8.cn


PDF ( 数据手册 , 数据表 ) LC78605E

零件编号 LC78605E
描述 Compact Disc Player DSP
制造商 Sanyo Semicon Device
LOGO Sanyo Semicon Device LOGO 


1 Page

No Preview Available !

LC78605E 数据手册, 描述, 功能
www.DataSheet4U.com
Ordering number : ENN7735
SANYO Semiconductors
DATA SHEET
CMOS IC
LC78605E Compact Disc Player DSP with
Built-in Microcontroller
Overview
The LC78605E CMOS IC implements the signal processing, servo control, LCD display, button state acquisition, and
remote controller handling required by compact disc players without requiring a separate microcontroller. It provides
the following basic functions: demodulation of the EFM signal from the optical pickup, deinterleaving, error detection
and correction, 8× oversampling audio filters, D/A converter (with built-in analog low-pass filter), LCD display drivers,
key acquisition (A/D) and control processing, and automatic discrimination and playback of CD-RW discs. Thus the
LC78604E is ideal for implementing low-end CD players that support playback of CD-RW discs.
The LC78604E also provides a radio tuner frequency display function, and allows digital display of the selected
frequency in manual tuning CD radio/cassette players.
Functions
• Implements the CD play/pause, stop, track selection, fast forward/fast rewind, repeat 1/repeat all, program
setup/play/clear for up to 30 tracks, and shuffle play functions controlled from CD player buttons.
<Signal-Processing Block>
• The signal-processing block applies slicing at the correct level to the input HF signal, and converts that signal to an
EFM signal. At the same time it generates a PLL clock signal with an average frequency of 4.3218MHz by
comparing the phase with that of the internal VCO.
• A reference clock signal and all necessary timings can be generated using an external 16.9344MHz crystal.
• The disc motor speed is controlled by a frame phase difference signal created from the playback clock and the
reference clock.
• Performs frame sync signal detection, protection, and interpolation to assure stable data readout.
• Demodulates the EFM signal and converts the result to 8-bit symbol data.
• Separates the subcode data from the EFM signal and outputs that data to the internal control processing block.
• After applying a CRC check to the subcode Q data, outputs that data to the internal control processing block.
• Buffers the demodulated EFM signal in internal RAM and compensates for up to ±4 frames of jitter due to
fluctuations in the disc speed.
• Applies unscrambling and deinterleaving to the demodulated EFM signal in the stipulated order.
• Performs error detection, correction, and flag processing (C1: double, C2: double).
• Sets the C2 flags according to the C1 flags and the C2 check and applies interpolation and previous value hold
processing to the output signal according to the C2 flags. This interpolation circuit implements 2-value
interpolation. A previous value hold operation is applied if the C2 flags indicate errors for over 2 consecutive
samples.
• The internal control processing block controls the track jump, focus start, disc motor start/stop, muting on/off, track
count, and other operations.
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
32504TN (OT) No.7735-1/11







LC78605E pdf, 数据表
LC78605E
Continued from preceding page.
Pin No. Pin Name I/O
Function
44 FMAMB I Tuner display switching selection input (Schmitt trigger input)
45 REMOTE I Remote control signal input (Schmitt trigger input)
Close switch detection signal input.
46 CLOSE I
A pull-up resistor is built in. (Schmitt trigger input)
Limit switch detection signal input.
47 PUIN I
A pull-up resistor is built in. (Schmitt trigger input)
48
DVSS
— Digital system ground. This pin must be connected to the 0 V level.
49
DVDD
— Digital system 3.3V power supply
50 TUNERIN I Tuner frequency display input
Internal signal monitor pin 3. (Schmitt trigger input)
51
MONI3
I/O
A pull-down resistor is built in. (Default: input mode)
Internal signal monitor pin 2. (Schmitt trigger input)
52
MONI2
I/O
A pull-down resistor is built in. (Default: input mode)
Internal signal monitor pin 1. (Schmitt trigger input)
53
MONI1
I/O
A pull-down resistor is built in. (Default: input mode)
Reset input for this IC’s tuner display block.
54 TUNERESB I A pull-down resistor is built in.
This pin must be set low briefly after power is first applied.
Reset input for this IC’s CD playback block.
55 CDRESB I A pull-down resistor is built in.
This pin must be set low briefly after power is first applied.
56
AD1
AI Key operation A/D converter input 1
57
AD2
AI Key operation A/D converter input 2
58
AD3
AI Key operation A/D converter input 3
59
AVSS
— Analog system ground. This pin must be connected to the 0V level.
60
PDO
AO
External VCO control phase comparator output
61
ISET
AI
PDO output current adjustment resistor connection
PLL system pins VCO frequency range adjustment
62 FR AI
An external resistor must be connected between this pin
and AVDD.
63
AVDD
— Analog system power supply
64
SLCO
AO Slice level control output
Pin state when
CDRESB is low
Pin state when
TUNERESB is low
(Low-level output)
Undefined
(Low-level output)
Undefined
(Low-level output)
Undefined
——
Undefined
Undefined
Undefined
Undefined
No.7735-8/11














页数 11 页
下载[ LC78605E.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
LC78605ECompact Disc Player DSPSanyo Semicon Device
Sanyo Semicon Device

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap