DataSheet8.cn


PDF ( 数据手册 , 数据表 ) TM0210AKFW

零件编号 TM0210AKFW
描述 LCD_Module
制造商 TIANMA
LOGO TIANMA LOGO 


1 Page

No Preview Available !

TM0210AKFW 数据手册, 描述, 功能
www.DSaPtaESCheIeFt4IUC.cMAoomTdeIlONoN.
FOR LCD
TM0210AKFW
MODULE
t4U.comPrepared by:
eeChecked by :
hVerified by :
www.DataSApproved by:
Date:
Date:
Date:
Date:
TIANMA MICROELECTRONICwSwCwO.D.,aLtaTSRDheve. 1e.0t4U.com







TM0210AKFW pdf, 数据表
4 Absolute Maximum Ratings(Ta=25 )
ITEM
SYMBOL MIN
Power supply
VBAT
3.0
voltage(1)
Power supply
LCD_VCC
-0.3
voltage(2)
Power supply
VLCD-GND -0.3
Voltage for main LCD
Logic signal Input Vt
-0.3
voltage
Operating temperature
Topr
-20
Storage temperature
Tst
-30
MAX
5.0
UNIT
V
4.0 V
20 V
LCD_VCC+0.3 V
+70
+80
Notes:
1. If the module is used above these absolute maximum ratings.It may become permanently
damaged.Using the module within the following electrical characteristic conditions are
also exceeded,the module will malfunction and cause poor reliability.
2. LCD_VCC>GND must be maintained.
7/28 R e v . 1 . 0







TM0210AKFW equivalent, schematic
Bit Pattern
1010 1000
1010 1001
1010 1011
1010 111D0
1011 P3P2P1P0
1100 S0XXX
1101 1F2F1F0
1110 0001
1110 0010
1110 0100
1110 1000
D7D6D5D4 D3D2D1D0
Command
NOP
Power Save Mode
Start Internal Oscillator
Display On/Off
Set Page Address
Set COM Scan Direction
Set Frame Frequency
Exit Power-save Mode
Software Reset
Release N-line Inversion
Mode
Display Data Length
Description
No operation
Sleep Mode:
Oscillator: OFF
LCD Power Supply: OFF
COM/SEG Outputs: VSS
This command starts the internal oscillator. Note that
the oscillator is OFF after reset, so this instruction must
be executed for initialization
Turn the display on and off without modifying the
content of the RAM. (0: off, 1: on)
This command has priority over Entire Display On/Off
and Invert Display On/Off. Commands are accepted
while the display is off, but the visual state of the
display does not change.
Set GDDRAM page address (0~8) using P3P2P1P0 for
RAM access. The page address is sets to 0 after reset.
Set the COM (row) scanning direction.
(0: COM0 COM63, 1: COM63 COM0)
This command is used to set the frame frequency.
F2F1F0
Frame Frequency
000 68
001 73
010 75 (POR)
011 80
100 80
101 86
110 90
111 100
DC-DC converter, regulator and divider status before
entering the power-save mode is restored. At POR,
Power-save Mode is released.
Reset some functions of the driver/controller. See
Reset Section below for more details.
Release the driver/controller from N-line inversion
mode. The frame will be inverted once per frame
This command is used in 3-line SPI mode (without D/C
line) to specify that the controller is about to send
display data to the display RAM. Eight bits are used to
specify the number of bytes to be sent (1 to 256 bytes).
The second command received after the display data is
transmitted is assumed to be command data.
15/28
Rev.1.0










页数 29 页
下载[ TM0210AKFW.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
TM0210AKFWLCD_ModuleTIANMA
TIANMA
TM0210AKFWDisplay ModuleTIANMA
TIANMA
TM0210AKFWspecLCD_ModuleTIANMA
TIANMA

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap