|
|
零件编号 | V30MLA0805L | ||
描述 | Multilayer Transient Voltage Surge Suppressors | ||
制造商 | Littelfuse | ||
LOGO | |||
1 Page
Next
Surface Mount Varistors
Multilayer Transient Voltage Surge Suppressors
ML Varistor Series
The ML Series family of Transient Voltage Surge Suppression devices is
based on the Littelfuse Multilayer fabrication technology. These compo-
nents are designed to suppress a variety of transient events, including
those specified in IEC 61000-4-2 or other standards used for Electromagnetic
Compliance (EMC). The ML Series is typically applied to protect integrated
circuits and other components at the circuit board level.
The wide operating voltage and energy range make the ML Series suit-
able for numerous applications on power supply, control and signal lines.
The ML Series is manufactured from semiconducting ceramics, and is
supplied in a leadless, surface mount package. The ML Series is compat-
ible with modern reflow and wave soldering procedures.
It can operate over a wider temperature range than zener diodes, and
has a much smaller footprint than plastic-housed components.
Littelfuse Inc. manufactures other Multilayer Series products. See the
MLE Series data sheet for ESD applications, MHS Series data sheet for
high-speed ESD applications, the MLN for multiline protection and the
AUML Series for automotive applications.
Features
• Leadless 0402, 0603, 0805, 1206 and 1210 Chip Sizes
• Multilayer Ceramic Construction Technology
•-55oC to +125oC Operating Temperature Range
• Operating Voltage Range VM(DC) = 5.5V to 120V
• Rated for Surge Current (8 x 20µs)
• Rated for Energy (10 x 1000µs)
• Inherent Bi-directional Clamping
• No Plastic or Epoxy Packaging Assures Better than 94V-0
Flammability Rating
• Standard Low Capacitance Types Available
Applications
• Suppression of Inductive Switching or Other Transient Events Such
as EFT and Surge Voltage at the Circuit Board Level
• ESD Protection for Components Sensitive to IEC 61000-4-2,
MIL-STD-883C Method 3015.7, and Other Industry Specifications
(See Also the MLE or MLN Series)
• Provides On-Board Transient Voltage Protection for ICs and Transistors
• Used to Help Achieve Electromagnetic Compliance of End Products
• Replace Larger Surface Mount TVS Zeners in
Many Applications
Previous
140 w w w . l i t t e l f u s e . c o m
Next
Previous
Surface Mount Varistors
Multilayer Transient Voltage Surge Suppressors
ML Varistor Series
Soldering Recommendations
The principal techniques used for the soldering of components in surface
mount technology are Infrared (IR) re-flow, vapour phase re-flow and wave
soldering. Typical profiles are shown in Figures 14, 15 and 16. When wave
soldering, the ML suppressor is attached to the circuit board by means of an
adhesive. The assembly is then placed on a conveyor and run through the
soldering process to contact the wave. With IR and vapour phase reflow; the
device is placed in a solder paste on the substrate. As the solder paste is
heated, it re-flows and solders the unit to the board.
The recommended solder for the ML suppressor is a 62/36/2 (Sn/Pb/Ag),
60/40 (Sn/Pb) or 63/37 (Sn/Pb). Littelfuse also recommends an RMA
solder flux.
Wave soldering is the most strenuous of the processes. To avoid the
possibility of generating stresses due to thermal shock, a preheat stage
in the soldering process is recommended, and the peak temperature of
the solder process should be rigidly controlled. For 0402 size devices, IR
re-flow is recommended.
When using a reflow process, care should be taken to ensure that the ML
chip is not subjected to a thermal gradient steeper than 4 degrees per
second; the ideal gradient being 2 degrees per second. During the
soldering process, preheating to within 100 degrees of the solder’s peak
temperature is essential to minimize thermal shock. Examples of the
soldering conditions for the ML suppressor are given in the tables below.
Once the soldering process has been completed, it is still necessary
to ensure that any further thermal shocks are avoided. One possible
cause of thermal shock is hot printed circuit boards being removed
from the solder process and subjected to cleaning solvents at room
temperature. The boards must be allowed to cool gradually to less than
50oC before cleaning.
Termination Options
Littelfuse offers three types of electrode termination finish for the
Multilayer product series:
1. Silver/Platinum (standard, not available for 0402)
2. Silver/Palladium (optional)
(The ordering information section describes how to designate them.)
3. Nickel Barrier (optional for 0402-1210 package size)
(The ordering information section describes how to designate them.)
250
MAXIMUM
TEMPERATURE 222oC
200
40-80
SECONDS
ABOVE 183 oC
150
RAMP RATE
<2oC /s
100
PREHEAT DWELL
50 PREHEAT ZONE
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
TIME (MINUTES)
FIGURE 14. REFLOW SOLDER PROFILE
300
MAXIMUM WAVE 260 oC
250
200
150
SECOND PREHEAT
100
FIRST PREHEAT
50
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
TIME (MINUTES)
FIGURE 15. WAVE SOLDER PROFILE
250
MAXIMUM
TEMPERATURE 222oC
200 40-80
SECONDS
ABOVE 183 oC
150
RAMP RATE
>50oC /s
100
PREHEAT ZONE
50
0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
TIME (MINUTES)
FIGURE 16. VAPOR PHASE SOLDER PROFILE
3.5
www.littelfuse.com
147
3
|
|||
页数 | 11 页 | ||
下载 | [ V30MLA0805L.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
V30MLA0805L | Multilayer Transient Voltage Surge Suppressors | Littelfuse |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |