DataSheet8.cn


PDF ( 数据手册 , 数据表 ) S6008DS2

零件编号 S6008DS2
描述 Sensitive SCRs
制造商 Teccor Electronics
LOGO Teccor Electronics LOGO 


1 Page

No Preview Available !

S6008DS2 数据手册, 描述, 功能
SUel.eLc.teRdEPFCailecOk#aGEg7eN1s6*IZ39ED
TO-202
3-lead
Compak
TO-92
TO-263
D2Pak
*TO-218
TO-252
D-Pak
*TO-218X
*TO-220
TO-251
V-Pak
A
K
G
(1 A to 70 A)
E6
General Description
The Teccor line of thyristor SCR semi-conductors are half-wave,
unidirectional, gate-controlled rectifiers which complement Tec-
cor's line of sensitive SCRs. Teccor offers devices with ratings of
1 A to 70 A and 200 V to 1000 V, with gate sensitivities from
10 mA to 50 mA. If gate currents in the 12 µA to 500 µA ranges
are required, see “Sensitive SCRs” section of this catalog.
Three packages are offered in electrically isolated construction
where the case or tab is internally isolated to allow the use of
low-cost assembly and convenient packaging techniques.
The Teccor line of SCRs features glass-passivated junctions to
ensure long-term reliability and parameter stability. Teccor’s
glass offers a rugged, reliable barrier against junction contamina-
tion.
Variations of devices covered in this data sheet are available for
custom design applications. Consult the factory for more informa-
tion.
Features
• Electrically-isolated package
• High voltage capability — 200 V to 1000 V
• High surge capability — up to 950 A
• Glass-passivated chip
Compak SCR
• Surface mount package — 1 A series
• New small profile three-leaded Compak package
• Packaged in embossed carrier tape with 2,500
devices per reel
• Can replace SOT-223
©2002 Teccor Electronics
Thyristor Product Catalog
E6 - 1
http://www.teccor.com
+1 972-580-7777







S6008DS2 pdf, 数据表
SCRs
Data Sheets
130
120
110
10 A TO-220
100 (Non-isolated)
16 A TO-220 (Non-isolated)
and TO-263
20 A TO-220 (Isolated)
10 A TO-251 and 10 A TO-252
90
12 A TO-220 (Non-isolated)
80 TO-251 and TO-252
70
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180˚
60 CASE TEMPERATURE: Measure as
shown on dimensional drawing
50
04 8
12
15 A TO-220
(Isolated)
16 20
RMS On-state Current [IT(RMS)] – Amps
Figure E6.7 Maximum Allowable Case Temperature versus
RMS On-state Current (10 A, 12 A, 16 A, and 20 A)
130
120
110
100
25 A TO-220
(Isolated)
90 25 A TO-220
(Non-isolated)
80 and TO-263
35 A TO-218
(Isolated)
70 CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
60 CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure
50 as shown on dimensional drawings
0 4 8 12 16 20 24 28
RMS On-state Current [IT(RMS)] – Amps
32
36
Figure E6.8 Maximum Allowable Case Temperature versus
RMS On-state Current (25 A and 35 A)
130
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
120 CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
110
100
65 A TO-218X
(Isolated)
90
70 A TO-218X
(Non-isolated)
80 55 A TO-218X
(Non-isolated)
70
60
40 A TO-220
(Non-isolated)
and TO-263
50
0
10 20 30 40 50 60
RMS On-state Current [IT(RMS)] – Amps
Figure E6.9 Maximum Allowable Case Temperature versus
RMS On-state Current (40 A through 70 A)
70
130
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
120 CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
110
55 A TO-220
100 (Non-isolated)
and TO-263 *
55 A TO-218AC
(Non-isolated) *
90 65 A TO-218AC
(Isolated) *
* The R, K or M package rating
80 is intended only for high surge
condition use and is not recommended
70 for >50 A rms continuous
current use, since narrow pin lead
temperature can exceed PCB solder
60 melting temperature. J or W packages
are recommended for >50 A rms
continuous current requirements.
50
0 10 20 30 40 50 60 70 75
RMS On-state Current [IT(RMS)] – Amps
Figure E6.10 Maximum Allowable Case Temperature versus
RMS On-state Current (55 A and 65 A)
130
120
110
100
1 A Devices
90
80
70 CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
60 CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
50
0 0.2 0.4 0.6
0.8
Average On-state Current [IT(AV)] – Amps
Figure E6.11 Maximum Allowable Case Temperature versus
Average On-state Current (1 A)
130
120
12 A TO-220 (Non-isolated)
and TO-251 and TO-252
10 A TO-251
10 A TO-252
110 6 A TO-220
6 A TO-202
100
90
6 A TO-251
6 A TO-252
8 A TO-220 (Isolated)
8 A TO-202
8 A TO-220
(Non-isolated)
CURRENT WAVEFORM: Sinusoidal
LOAD: Resistive or Inductive
CONDUCTION ANGLE: 180˚
CASE TEMPERATURE: Measure as
shown on dimensional drawings
10 A TO-220
(Non-isolated)
10 A TO-220 (Isolated)
and 10 A TO-202
80
0
123 456 7
Average On-state Current [IT(AV)] – Amps
8
Figure E6.12 Maximum Allowable Case Temperature versus
Average On-state Current (8 A, 10 A, and 12 A)
http://www.teccor.com
+1 972-580-7777
E6 - 8
©2002 Teccor Electronics
Thyristor Product Catalog














页数 12 页
下载[ S6008DS2.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
S6008DS2Sensitive SCRsTeccor Electronics
Teccor Electronics
S6008DS3Sensitive SCRsTeccor Electronics
Teccor Electronics

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap