DataSheet8.cn

DAC7613EB 数据手册 PDF ( 12-Bit/ Voltage Output DIGITAL-TO-ANALOG CONVERTER )

零件编号 DAC7613EB
描述 12-Bit/ Voltage Output DIGITAL-TO-ANALOG CONVERTER
制造商 Burr-Brown Corporation
LOGO Burr-Brown Corporation LOGO 

1 Page
		

No Preview Available !

DAC7613EB 数据手册, 描述, 功能
®
DAC7613
DAC7613
For most current data sheet and other product
information, visit www.burr-brown.com
12-Bit, Voltage Output
DIGITAL-TO-ANALOG CONVERTER
FEATURES
q LOW POWER: 1.8mW
q UNIPOLAR OR BIPOLAR OPERATION
q SETTLING TIME: 10µs to 0.012%
q 12-BIT LINEARITY AND MONOTONICITY:
–40°C to +85°C
q DATA READBACK
q DOUBLE-BUFFERED DATA INPUTS
q 24-LEAD SSOP PACKAGE
APPLICATIONS
q PROCESS CONTROL
q CLOSED-LOOP SERVO-CONTROL
q MOTOR CONTROL
q DATA ACQUISITION SYSTEMS
DESCRIPTION
The DAC7613 is a 12-bit, voltage output digital-to-
analog converter with guaranteed 12-bit monotonic
performance over the specified temperature range.
The DAC7613 accepts a 12-bit parallel input data, has
double-buffered DAC input logic and provides a
readback mode of the internal input register. An asyn-
chronous reset clears all registers to a mid-scale code
of 800H or to a zero-scale of 000H. The DAC7613 can
operate from a single +5V supply or from +5V and
–5V supplies.
Low power and small size makes the DAC7613 ideal
for data acquisition systems and closed-loop servo-
control. The DAC7613 is available in a plastic
SSOP-24 package, and offers guaranteed specifica-
tions over the –40°C to +85°C temperature range.
Data I/O
12
CS
R/W
I/O
Buffer
VREFL VREFH
VDD VSS
Input
Register
DAC
Register
TS
DAC
RESET RESETSEL LOADDAC
VOUT
DAC7613
GND
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
© 1998 Burr-Brown Corporation
PDS-11500B
DPrAintCed 7in 6U.1S.A3. January, 2000
®




DAC7613EB pdf, 数据表
ANALOG OUTPUTS
When VSS = –5V (dual supply operation), the output ampli-
fier can swing to within 2.25V of the supply rails, guaran-
teed over the –40°C to +85°C temperature range. With
VSS = 0V (single-supply operation), the output can swing to
ground. Note that the settling time of the output op amp will
be longer with voltages very near ground. Additionally, care
must be taken when measuring the zero-scale error when
VSS = 0V. Since the output voltage cannot swing below
ground, the output voltage may not change for the first few
digital input codes (000H, 001H, 002H, etc.) if the output
amplifier has a negative offset.
The behavior of the output amplifier can be critical in some
applications. Under short-circuit conditions (DAC output
shorted to ground), the output amplifier can sink a great deal
more current than it can source. See the Specifications table
for more details concerning short-circuit current.
REFERENCE INPUTS
The reference inputs, VREFL and VREFH, can be any voltage
between VSS + 2.25V and VDD – 2.25V provided that VREFH
is at least 1.25V greater than VREFL. The minimum output of
each DAC is equal to VREFL plus a small offset voltage
(essentially, the offset of the output op amp). The maximum
output is equal to VREFH plus a similar offset voltage. Note
that VSS (the negative power supply) must either be
connected to ground or must be in the range of –4.75V to
–5.25V. The voltage on VSS sets several bias points within
the converter. If VSS is not in one of these two configura-
tions, the bias values may be in error and proper operation
of the device is not guaranteed.
The current into the VREFH input depends on the DAC output
voltages and can vary from a few microamps to approxi-
mately 0.1 milliamp. The VREFH source will not be required
to sink current, only source it. Bypassing the reference
voltage or voltages with at least a 0.1µF capacitor placed as
close to the DAC7613 package is strongly recommended.
DIGITAL INTERFACE
Table I shows the basic control logic for the DAC7613. Note
that the internal register is level triggered and not edge
triggered. When the appropriate signal is LOW, the register
becomes transparent. When this signal is returned HIGH, the
digital word currently in the register is latched. The first
register (the input register) is triggered via the R/W, and CS
inputs. The second register (the DAC register) is transparent
when LOADDAC input is pulled LOW.
The double-buffered architecture is mainly designed so that
the DAC input register can be written at any time and then
the DAC voltage updated by pulling LOADDAC LOW.
R/W CS RST LOADDAC
L LH
L LH
HLH
XHH
XHH
XH L
L
H
H
L
H
X
X = Don’t Care.
INPUT
REGISTER
Write
Write
Read
Hold
Hold
Hold
DAC
REGISTER
Write
Hold
Hold
Update
Hold
Reset
MODE
Write
Write Input
Read Input
Update
Hold
Reset
TABLE I. DAC7613 Control Logic Truth Table.
®
DAC7613
8





页数 9 页
下载[ DAC7613EB.PDF 数据手册 ]

分享链接

Link 1 :
Link 2 :

推荐数据表

零件编号描述制造商
DAC7613E12-Bit/ Voltage Output DIGITAL-TO-ANALOG CONVERTERBurr-Brown Corporation
Burr-Brown Corporation
DAC7613EB12-Bit/ Voltage Output DIGITAL-TO-ANALOG CONVERTERBurr-Brown Corporation
Burr-Brown Corporation

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


www.DataSheet8.cn    |   2018   |  联系我们   |   搜索