DataSheet8.cn


PDF ( 数据手册 , 数据表 ) DAC716UK

零件编号 DAC716UK
描述 16-Bit DIGITAL-TO-ANALOG CONVERTER with Serial Data Interface
制造商 Burr-Brown Corporation
LOGO Burr-Brown Corporation LOGO 


1 Page

No Preview Available !

DAC716UK 数据手册, 描述, 功能
® DAC716
16-Bit DIGITAL-TO-ANALOG CONVERTER
with Serial Data Interface
FEATURES:
q SERIAL DIGITAL INTERFACE
q VOLTAGE OUTPUT: 0 to +10V
q ±2 LSB INTEGRAL LINEARITY
q PRECISION INTERNAL REFERENCE
q LOW NOISE: 120nV/Hz Including Reference
q 16-LEAD PLASTIC SKINNY DIP AND PLASTIC
SOIC PACKAGES
DESCRIPTION
The DAC716 is a complete monolithic D/A converter
including a +10V temperature compensated voltage
reference, current-to-voltage amplifier, a high-speed
synchronous serial interface, a serial output which
allows cascading multiple converters, and an asyn-
chronous clear function which immediately sets the
output voltage to zero.
The output voltage range is 0 to +10V while operating
from ±12V to ±15V supplies, and the gain and bipolar
offset adjustments are designed so that they can be set
via external potentiometers or external D/A convert-
ers. The output amplifier is protected against short-
circuiting to ground.
The 16-pin DAC716 is available in a plastic 0.3" DIP
and a wide-body plastic SOIC package. The DAC716P,
U, PB, and UB are specified over the –40°C to +85°C
range while the DAC716UK and PK are specified
over the 0°C to +70°C range.
A0
A1
SDI
CLK
CLR
Reference
Circuit
Gain
Adjust
VREF OUT
+10V
Input Shift Register
16
D/A Latch
16
16-Bit D/A Converter
Offset Adjust
SDO
VOUT
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
© 1996 Burr-Brown Corporation
PDS-1324B
Printed in U.S.A. March, 1998







DAC716UK pdf, 数据表
DAC716 CALIBRATION VALUES
1 LEAST SIGNIFICANT BIT = 152µV
DIGITAL INPUT CODE ANALOG OUTPUT (V)
STRAIGHT BINARY UNIPOLAR 10V RANGE DESCRIPTION
FFFFH
|
8000H
+9.999695
+5.000000
+ Full Scale –1LSB
Half Scale
0000H
0.000000
Unipolar Zero
TABLE I. Digital Input and Analog Output Voltage Calibra-
tion Values.
INSTALLATION
GENERAL CONSIDERATIONS
Due to the high precision of these D/A converters, system
design problems such as grounding and contact resistance
become very important. A 16-bit converter with a 10V full-
scale range has a 1LSB value of 152µV. With a load current
of 5mA, series wiring and connector resistance of only
60mwill cause a voltage drop of 300µV. To understand
what this means in terms of a system layout, the resistivity
of a typical 1 ounce copper-clad printed circuit board is 1/2
mper square. For a 5mA load, a 0.1 inch wide printed
circuit conductor 0.6 inches long will result in a voltage drop
of 150µV.
The analog output of DAC716 has an LSB size of 152µV
(–96dB). The rms noise floor of the D/A should remain below
this level in the frequency range of interest. The DAC716’s
output noise spectral density (which includes the noise contrib-
uted by the internal reference) is shown in the Typical Perfor-
mance Curves section.
Wiring to high-resolution D/A converters should be routed
to provide optimum isolation from sources of RFI and EMI.
The key to elimination of RF radiation or pickup is small
loop area. Signal leads and their return conductors should be
kept close together such that they present a small capture
cross-section for any external field. Wire-wrap construction
is not recommended.
POWER SUPPLY AND
REFERENCE CONNECTIONS
Power supply decoupling capacitors should be added as
shown in Figure 4. Best performance occurs using a 1 to
10µF tantalum capacitor at –VCC. Applications with less
critical settling time may be able to use 0.01µF at –VCC
as well as at +VCC. The capacitors should be located
close to the package.
The DAC716 has separate ANALOG COMMON and DIGI-
TAL COMMON pins. The current through DCOM is mostly
switching transients and are up to 1mA peak in amplitude.
The current through ACOM is typically 5µA for all codes.
Use separate analog and digital ground planes with a single
interconnection point to minimize ground loops. The analog
+12V to +15V
+
1µF
1 16
2 –VCC 15
3 14
4 13
DAC716
5 12
6 DCOM
11
7 +VCC
8 ACOM
10
9
–12V to –15V
+ 1µF
FIGURE 4. Power Supply Connections.
pins are located adjacent to each other to help isolate analog
from digital signals. Analog signals should be routed as far
as possible from digital signals and should cross them at
right angles. A solid analog ground plane around the D/A
package, as well as under it in the vicinity of the analog and
power supply pins, will isolate the D/A from switching
currents. It is recommended that DCOM and ACOM be
connected directly to the ground planes under the package.
If several DAC716s are used or if the DAC716 shares
supplies with other components, connecting the ACOM and
DCOM lines together at the power supplies only rather than
at each chip, may give better results.
LOAD CONNECTIONS
Since the reference point for VOUT and VREF OUT is the
ACOM pin, it is important to connect the D/A converter load
directly to the ACOM pin. Refer to Figure 5.
Lead and contact resistances are represented by R1 through
R3. As long as the load resistance RL is constant, R1 simply
introduces a gain error and can be removed by gain adjust-
ment of the D/A or system-wide gain calibration. R2 is part
of RL if the output voltage is sensed at ACOM.
In some applications it is impractical to return the load to the
ACOM pin of the D/A converter. Sensing the output voltage
at the SYSTEM GROUND point is reasonable, because there
is no change in DAC716 ACOM current, provided that R3 is
a low-resistance ground plane or conductor. In this case you
may wish to connect DCOM to SYSTEM GROUND as well.
GAIN AND OFFSET ADJUST
Connections Using Potentiometers
GAIN and OFFSET adjust pins provide for trim using
external potentiometers. 15-turn potentiometers provide suf-
ficient resolution. Range of adjustment of these trims is at
least ±0.3% of Full Scale Range. Refer to Figure 6.
®
DAC716
8














页数 13 页
下载[ DAC716UK.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
DAC716U16-Bit DIGITAL-TO-ANALOG CONVERTER with Serial Data InterfaceBurr-Brown Corporation
Burr-Brown Corporation
DAC716UB16-Bit DIGITAL-TO-ANALOG CONVERTER with Serial Data InterfaceBurr-Brown Corporation
Burr-Brown Corporation
DAC716UK16-Bit DIGITAL-TO-ANALOG CONVERTER with Serial Data InterfaceBurr-Brown Corporation
Burr-Brown Corporation

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap