DataSheet8.cn


PDF ( 数据手册 , 数据表 ) MI0177JT-1

零件编号 MI0177JT-1
描述 LCD Module
制造商 MULTI-INNO TECHNOLOGY
LOGO MULTI-INNO TECHNOLOGY LOGO 


1 Page

No Preview Available !

MI0177JT-1 数据手册, 描述, 功能
MULTI-INNO TECHNOLOGY CO., LTD.
www.multi-inno.com
LCD MODULE SPECIFICATION
Model : MI0177JT-1
For Customer's Acceptance:
Customer
Approved
Comment
Revision
Engineering
Date
Our Reference
1.2
2012-07-23







MI0177JT-1 pdf, 数据表
MODULE NO.: MI0177JT-1
FIG.1. The definition of Response Time
Ver 1.2
FIG.2. Measuring method for Contrast ratio,surface luminance, Luminance uniformity,CIE (x,
y) chromaticity
A : 5 mm
B : 5 mm
H,V : Active Area
Light spot size =5mm, 500mm distance from the
LCD surface to detector lens
measurement instrument is TOPCON’s luminance
meter BM-5
FIG.3. The definition of viewing angle
MULTI-INNO TECHNOLOGY CO.,LTD.
P.8







MI0177JT-1 equivalent, schematic
MODULE NO.: MI0177JT-1
Ver 1.2
PRECAUTIONS FOR USING LCD MODULES
1 Handing Precautions
1.1 The display panel is made of glass and polarizer. As glass is fragile. It tends to become or
chipped during handling especially on the edges. Please avoid dropping or jarring. Do not
subject it to a mechanical shock by dropping it or impact.
1.2 If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any
in your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause
the color tone to vary. Do not touch the display with bare hands. This will stain the display area
and degraded insulation between terminals (some cosmetics are determined to the polarizer).
1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched.
Handle this polarizer carefully. Do not touch, push or rub the exposed polarizers with anything
harder than an HB pencil lead (glass, tweezers, etc.). Do not put or attach anything on the
display area to avoid leaving marks on it. Condensation on the surface and contact with
terminals due to cold will damage, stain or dirty the polarizer. After products are tested at low
temperature they must be warmed up in a container before coming in to contact with room
temperature air.
1.5 If the display surface becomes contaminated, breathe on the surface and gently wipe it with a
soft dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents
- Isopropyl alcohol
- Ethyl alcohol
Do not scrub hard to avoid damaging the display surface.
1.6 Solvents other than those above-mentioned may damage the polarizer. Especially, do not use
the following.
- Water
- Ketone
- Aromatic solvents
Wipe off saliva or water drops immediately, contact with water over a long period of time
may cause deformation or color fading. Avoid contact with oil and fats.
1.7 Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated
by water droplets, moisture condensation or a current flow in a high-humidity environment.
1.8 Install the LCD Module by using the mounting holes. When mounting the LCD module make
sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the
I/O cable or the backlight cable.
1.9 Do not attempt to disassemble or process the LCD module.
1.10 NC terminal should be open. Do not connect anything.
1.11 If the logic circuit power is off, do not apply the input signals.
1.12 Electro-Static Discharge Control Since this module uses a CMOS LSI, the same careful
attention should be paid to electrostatic discharge as for an ordinary CMOS IC. To prevent
destruction of the elements by static electricity, be careful to maintain an optimum work
environment.
- Before removing LCM from its packing case or incorporating it into a set, be sure
the module and your body have the same electric potential. Be sure to ground the body when
handling the LCD modules.
- Tools required for assembling, such as soldering irons, must be properly grounded.
Make certain the AC power source for the soldering iron does not leak. When using an
electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to
minimize as much as possible any transmission of electromagnetic waves produced sparks
coming from the commutator of the motor.
- To reduce the amount of static electricity generated, do not conduct assembling
MULTI-INNO TECHNOLOGY CO.,LTD.
P.16










页数 22 页
下载[ MI0177JT-1.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
MI0177JT-1LCD ModuleMULTI-INNO TECHNOLOGY
MULTI-INNO TECHNOLOGY

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap