|
|
零件编号 | MI0283KT | ||
描述 | LCD MODULE | ||
制造商 | MULTI-INNO TECHNOLOGY | ||
LOGO | |||
1 Page
MULTI-INNO TECHNOLOGY CO., LTD.
LCD MODULE SPECIFICATION
Model : MI0283KT
Revision
Engineering
Date
Our Reference
P.1
MODULE NO.: MI0283KT
Ver 1.0
n INTERFACE DESCRIPTION
Pin No. Symbol
Level
1 LEDK
-
2~5 LEDA1~A4
-
IM0
Description
LED light cathode.
LED light anode.
Select a mode to interface to an MPU. In SPI mode, the IM0
pin is used to set the ID of device code.
IM1
6~9
IM2
H/L
IM3
10
11
12
13
14
15~32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
RESET
VSYNC
HSYNC
DOTCLK
ENABLE
DB17~DB0
SDO
SDI
RD
WR/SCL
RS
CS
FMARK
IOVCC
VCC
VCI
GND
X+
Y+
X-
Y-
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
H/L
1.65~3.3V
2.5~3.3V
2.5~3.3V
0V
-
-
-
-
Reset signal.
Frame synchronous signal for RGB interface operation.
Line synchronous signal for RGB interface operation.
Dot clock signal for RGB interface operation.
Data enable signal for RGB interface operation.
Data bus.
Serial data output pin in SPI mode.
Serial data input pin in SPI mode.
Read signal.
Write strobe signal in 80-system bus interface operation and
enables write operation when WR is low. Synchronous clock
signal (SCL) in serial interface operation.
Command / data select.
Chip selection.
Frame head pulse signal.
Interface I/O power supply.
Logic regulator power supply.
Liquid crystal analog circuit power supply.
Ground.
Touch panel coordinate in the right side of envisage drawing.
Touch panel coordinate in the down side of envisage drawing.
Touch panel coordinate in the left side of envisage drawing.
Touch panel coordinate in the up side of envisage drawing.
n APPLICATION CIRCUIT
Please consult our technical department for detail information.
n INITIAL CODE
Please consult our technical department for detail information.
MULTI-INNO TECHNOLOGY CO.,LTD.
P.8
MODULE NO.: MI0283KT
Ver 1.0
OUTGOING QUALITY STANDARD
PAGE 7 OF 7
TITLE: FUNCTIONAL TEST & INSPECTION CRITERIA
1、 Pattern font:
Pattern fonts are clear and symmetrical,pattern fonts filter lightly
are allowed; The fort line is not allow to thinner or thicker than
1/3of normal size, and swing is not more than 0.1mm. the line is
smooth and not broken.
2、The wing forward in the side of Visual Area:
The length of wing forward inside of the Visual Area: n≤0.2mm;
Not excess 3 point,and the distanceD≥20mm。
4.4.3
TP Defect
3、Film impression:With operation, must be invisibility.
4、Touch panel knob:if writing function normally,it could be
allowed.
Minor
5、 Newton ring
Without operation, the color circle of Regularity or Non-regularity
from the normal or slope angle of view.
1、Regularity: The area of the newton ring is less than 1/3 area
of the touch panel; and no character affected and line distorted
after touch panel lightening. It’s ok.
2、 Non-regularity : The area of the Newton ring is less than
the 1/2 area of touch panel with lightening. And no character
affected and line
MULTI-INNO TECHNOLOGY CO.,LTD.
P.16
|
|||
页数 | 23 页 | ||
下载 | [ MI0283KT.PDF 数据手册 ] |
零件编号 | 描述 | 制造商 |
MI0283KT | LCD MODULE | MULTI-INNO TECHNOLOGY |
零件编号 | 描述 | 制造商 |
STK15C88 | 256-Kbit (32 K x 8) PowerStore nvSRAM | Cypress Semiconductor |
NJM4556 | DUAL HIGH CURRENT OPERATIONAL AMPLIFIER | New Japan Radio |
EL1118-G | 5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLER | Everlight |
DataSheet8.cn | 2020 | 联系我们 | 搜索 | Simemap |