DataSheet8.cn


PDF ( 数据手册 , 数据表 ) PD050QT2

零件编号 PD050QT2
描述 Display Module
制造商 Prime View
LOGO Prime View LOGO 


1 Page

No Preview Available !

PD050QT2 数据手册, 描述, 功能
Version : 1.0
P-511-461(V:1)
PD050QT2
TECHNICAL SPECIFICATION
MODEL NO : PD050QT2
The content of this information is subject to be changed without notice.
Please contact PVI or its agent for further information.
Customer’s Confirmation
Customer
Date
By
PVI’s Confirmation
Confirmed By
Prepared By
The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:1







PD050QT2 pdf, 数据表
P-511-461(V:1)
8. Electrical Characteristics
8-1) Recommended Operating Conditions:
Item
Supply Voltage
Current Dissipation
Total power consumption
Permissive input ripple voltage
Input voltage(Low)
Input voltage(High)
Vcom Voltage
Symbol
VCC
ICC
PCC
VRF
VIL
VIH
Vcom
PD050QT2
Min.
+3.0
-
128.4
-
0
0.7 VCC
-
Typ.
+3.3
42.8
141.24
-
-
-
3.55
Max.
+3.6
-
154.08
100
0.3 VCC
VCC
-
GND=0V, Ta=25
Unit Remark
V
mA Note 8-1
mW
mVp-p VCC=3.3V
V
V
V
Note 8-1 : To test the current dissipation of VCC, using the “color bars” testing pattern shown as below.
12345678
IDD current dissipation testing pattern
1. White
2. Yellow
3. Cyan
4. Green
5. Magenta
6. Red
7. Blue
8. Black
8-2) Recommended Driving Condition for Back Light
Parameter
Symbol
Supply voltage of LED backlight
VLED1~8
Supply current of LED backlight
ILED1~8
Backlight Power Consumption
PLED
Note 8-2 : ILED1~8=20mA, Constant Current
Min
-
-
-
GND = 0 VTa = 25
TYP MAX Unit
Remark
- (11.0) V
Note 8-2
20 - mA
Note 8-3
- 1.76 W
Note 8-4
Note 8-3 : The LED driving condition is defined for each LED module. (3 LED Serial)
Input current = 20mA * 8 = 160mA
Note 8-4 : PLED = VLED-1 * ILED-1 + VLED-2* ILED-2 ….. + VLED-7 * ILED-7+VLED-8 * ILED-8
VLED-1
VLED-2
Anode
Cathode
VLED-7
VLED-8
The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:8







PD050QT2 equivalent, schematic
P-511-461(V:1)
PD050QT2
13. Handling Cautions
13-1) Mounting of module
A) Please power off the module when you connect the input/output connector.
B) Polarizer which is made of soft material and susceptible to flaw must be handled carefully.
C) Protective film (Laminator) is applied on surface to protect it against scratches and dirt. It
is recommended to peel off the laminator before use and taking care of static electricity.
13-2) Precautions in mounting
A) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with
soft dry cloth.
B) Wipe off water drops or finger grease immediately. Long contact with water may cause
discoloration or spots.
C) TFT-LCD module uses glass, which breaks or cracks easily if dropped or bumped on hard
surface. Please handle with care.
D) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself
when handling.
13-3) Adjusting module
A) Adjusting volumes on the rear face of the module have been set optimally before shipment.
B) Therefore, do not change any adjusted values. If adjusted values are changed, the
specifications described may not be satisfied.
13-4) Others
A) Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours.
B) Store the module at a room temperature place.
C) The voltage of beginning electric discharge may over the normal voltage because of
leakage current from approach conductor by to draw lump read lead line around.
D) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel.
Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash
it out immediately with soap.
E) Observe all other precautionary requirements in handling general electronic components.
F) Please adjust the voltage of common electrode as material of attachment by 1 module.
13-5) Polarizer mark
The polarizer mark is to describe the direction of view angle film how to mach up with the
rubbing direction.
The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed,
reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd.PAGE:16










页数 19 页
下载[ PD050QT2.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
PD050QT1Display ModulePrime View
Prime View
PD050QT2Display ModulePrime View
Prime View

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap