DataSheet8.cn


PDF ( 数据手册 , 数据表 ) SJ1117-15PI

零件编号 SJ1117-15PI
描述 Adjustable and Fixed Voltage Regulator
制造商 AUK
LOGO AUK LOGO 


1 Page

No Preview Available !

SJ1117-15PI 数据手册, 描述, 功能
SJ1117xxx
Adjustable and Fixed Voltage Regulator
Descriptions
The SJ1117 series of positive adjustable and fixed regulators are designed to provide 1A with high efficiency.
All internal circuitry is designed to operate down to 1.1V input to output differential.
The SJ1117 offers current limiting and thermal shutdown and over voltage protection.
Features
Adjustable or fixed output(1.2V, 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5V)
Output current of 1A
Safe Operating Area(SOA) Protection
Over Voltage Protection (OVP)
Over Current Protection (OCP)
Thermal shutdown protection
Low dropout, 1.1V Typical at 1A output current
Operating temperature range : -40~ +125
Halogen-Free Package is Available
High Level ESD Protection : 400V(MM), 4KV(HBM)
Typical Applications
VIN
IN SJ1117-XX OUT
+ CIN
10uF
GND
VOUT
+ CO
10uF
VIN
+ CIN
10uF
IN
SJ1117A
ADJ
OUT
VOUT
R1
125Ω
+ CO
10uF
R2
225Ω
Fig.1 Fixed Voltage Regulator
Fig.2 Adjustable Voltage Regulator
Notes
Vout
=
VADJ
× (1+
R2
R1
)
+
I ADJ
×
R2
1) CIN needed if device is far from filter capacitors
2) CO minimum value required for stability
KSD-I0T005-008
1







SJ1117-15PI pdf, 数据表
SJ1117xxx
Application Note
Input Bypass Capacitor (CIN)
An Input capacitor is recommended. A 10μF tantalum capacitor on the input is a suitable bypassing for all
applications.
Adjust Terminal Bypass Capacitor(CADJ)
The adjust terminal can be bypassed to ground with a bypass capacitor to improve ripple rejection
This bypass capacitor prevents ripple from being amplified as the output voltage is increased. At
any ripple frequency, the impedance of the CADJ should less than R1 to prevent the ripple from being
amplified
1
(2π × f RIPPLE × C ADJ )
R1
The R1 is the resistor between the output and the adjust pin.
Output Capacitor(COUT)
The output capacitor(COUT) is critical in maintaining regulator stability, and must meet required
conditions for both minimum amount of capacitance and ESR. The minimum COUT required is
10μF(tantalum capacitor). Any increase of the COUT will merely improve the stability and transient
response. The ESR of the COUT should range between 0.3- 22. In the case of the adjustable regulator,
when the CADJ is used, a larger COUT (22μF) is required.
Output Voltage
The SJ1117 develops a 1.25V reference voltage between the output and the adjust terminal (See Fig.9).
By placing a resistor between these two terminals, a constant current is caused to flow through R1 and
down through R2 to set the overall output voltage. Normally this current is chosen to be the specified
minimum load current. Because IADJ is very small and constant when compared to the current through R1,
it represents a small error and can usually be ignored. For fixed voltage devices R1 and R2 are included in
the device.
VIN
+ CIN
IN
SJ1117
ADJ
OUT
VREF
VOUT
+ CO
R1
IADJ
( )VOUT
= VREF
1
+
R2
R1
+ I ADJ × R2
R2
Fig.13 Basic Adjustable Regulator
KSD-I0T005-008
8







SJ1117-15PI equivalent, schematic
TO-220F-3L Outline Dimension (unit : mm)
SJ1117xxx
KSD-I0T005-008
16










页数 18 页
下载[ SJ1117-15PI.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
SJ1117-15PIAdjustable and Fixed Voltage RegulatorAUK
AUK

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap