DataSheet8.cn


PDF ( 数据手册 , 数据表 ) BM1P066FJ

零件编号 BM1P066FJ
描述 PWM Control IC
制造商 ROHM Semiconductor
LOGO ROHM Semiconductor LOGO 


1 Page

No Preview Available !

BM1P066FJ 数据手册, 描述, 功能
Datasheet
AC/DC Drivers
PWM Control IC
BM1P066FJ
General
The PWM control IC for AC/DC “BM1P066FJ”
provides an optimum system for all products that
include an electrical outlet.
A built-in start circuit that withstands 650 V helps to
keep power consumption low. Both isolated and
non-isolated versions are supported, making for
simpler design of various types of low-power
converters. Switching MOSFET and current detection
resistors are external devices, thus achieving a higher
degree of freedom in power supply design. The
switching frequency is set as fixed. Since current mode
control is used, a current limit is imposed in each cycle,
and excellent performance is demonstrated in
bandwidth and transient response. With a light load,
frequency is reduced and higher efficiency is realized.
A frequency hopping function is also built in,
contributing to low EMI.
Also on chip are soft start and burst functions, a
per-cycle overcurrent limiter, VCC overvoltage
protection, overload protection, and other protection
functions.
Basic Specifications
Operating power supply voltage range: VCC 8.9 V to 26.0 V
VH: to 600 V
Operating current:
Normal: 0.60 mA (Typ.)
Burst mode: 0.35 mA (Typ.)
Oscillation frequency:
BM1P066FJ: 65 kHz (Typ.)
Operating temperature range:
-40°C to +85°C
Application circuit
Features
PWM frequency: 65 kHz
PWM current mode method
Frequency hopping function
Burst operation during light load / Frequency
reduction function
650 V start circuit
VCC pin undervoltage protection
VCC pin overvoltage protection
CS pin open protection
CS pin Leading-Edge-Blanking function
Per-cycle overcurrent limiter function
Overcurrent limiter with AC voltage compensation
function
Soft start function
Secondary overcurrent protection circuit
Package
SOP-J8
4.90 mm × 6.00 mm × 1.65 mm pitch 1.27 mm
(Typ.)
(Typ.) (Typ.)
(Typ.)
Applications
AC adapters, TV s, and household appliances
(vacuum cleaners, humidifiers, air cleaners, air
conditioners, IH cooking heaters, rice cookers, etc.)
Line-up
Frequency VCCOVP VCC recharge
BM1P061FJ
BM1P062FJ
BM1P063FJ
BM1P064FJ
BM1P065FJ
BM1P066FJ
BM1P067FJ
BM1P068FJ
BM1P101FJ
BM1P102FJ
BM1P103FJ
BM1P104FJ
BM1P105FJ
BM1P106FJ
BM1P107FJ
BM1P108FJ
65kHz
65kHz
65kHz
65kHz
65kHz
65kHz
65kHz
65kHz
100kHz
100kHz
100kHz
100kHz
100kHz
100kHz
100kHz
100kHz
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
Auto-restart
Latch
×
×
×
×
×
×
×
×
X-cap
discharge
×
×
×
×
×
×
×
×
×
×
×
×
Brown-out
×
×
×
×
×
×
×
×
Figure 1Application Circuit
Product structureSilicon monolithic integrated circuit
.www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
This product is not designed for protection against radioactive rays
1/27
TSZ02201-0F2F0A200200-1-2
30.Oct.2013.Rev.001







BM1P066FJ pdf, 数据表
BM1P066FJ
Datasheet
(2) Startup sequences (soft start operation, light load operation, auto recovery operation during overload protection)
Startup sequences are shown in Figure 8.
See the sections below for detailed descriptions.
Figure 8. Startup Sequence Time Chart
A: Voltage is applied to the input voltage (VH) pin (pin 8).
B: The VCC pin (pin 6) voltage rises, and when VCC VUVLO1 (13.5 V typ) this IC starts to operate.
When protection functions (ACMONI, VCC, CS, FB pin, temperature) are judged as normal, switching operation begins.
At this time, the VCC pin (pin 6) consumption current necessarily causes the VCC pin voltage to drop.
When VCC < VUVLO2 (8.2 V typ), switching operation stops by VCC UVLO function. For that, set VCC capacitor to finish
start-up before VCC<VUVLO2(8.2V.typ)
C: With the soft start function, excessive rises in voltage and current are prevented by adjusting the voltage level of the CS
pin (pin 3). During a soft start, the IC changes the overcurrent detection voltage from VCC_SS1 to VCC_SS4 to prevent
overshoot of the output voltage. VCC_SS1 is described in Table 2 below.
Table 2 Overcurrent Detection Voltage at Startup
Soft start
Vlim1
Start ~  0.5 ms
0.10 V (12%)
0.5 ms  ~1 ms
1 ms  ~2 ms
2 ms  ~ 4 ms
0.15 V (25%)
0.20 V (50%)
0.30 V (75%)
4 ms ~
0.500 V (100%)
D: When the switching operation starts, the secondary output voltage VOUT rises.
After switching has started, set the output voltage to within TFOLP (64 ms typ) to become the rated voltage.
E: When there is a light load, burst operation suppresses power consumption.
F: When there is an overload, the FB pin (pin 2) voltage becomes greater than VFOLP1A to reduce the output voltage.
G: If the FB pin (pin 2) voltage exceeds VFOLP1A for TFOLP (64ms typ) or longer, the overload protection circuit stops the
switching operation. For that, set to finish the start-up time within TFOLP (64 ms typ).
When the FB pin (pin 2) voltage exceeds VFOLP1B, the IC’s internal timer TFOLP (64 ms typ) is reset.
H: When VCC voltage becomes VCC < VUVLO2 (8.2 V typ), the start circuit operates and VCC charging is started.
I: When VCC voltage becomes VCC> VUVLO1 (13.5 V typ), the start circuit stops charging VCC.
J: Same as F
K: Same as G
Startup waveforms are shown as reference examples in Figure 9 and Figure 10.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
8/27
TSZ02201-0F2F0A200200-1-2
30.Oct.2013.Rev.001







BM1P066FJ equivalent, schematic
BM1P066FJ
Datasheet
(6) L.E.B period
When the driver MOSFET is turned on, a surge current is generated at time point A in Figure 16.
At that time, the CS voltage (pin 4) rises, which may cause detection errors in the overcurrent limiter circuit.
To prevent these detection errors, the OUT pin in this IC is switched from low to high and the CS voltage (pin 4) is
masked for 250 ns by the built-in L.E.B function (Leading Edge Blanking function).
This blanking function can reduce the CS pin noise filter for the noise that is generated when switching the OUT pin from
low to high.
However, if the CS pin noise does not stay within this 250 ns period, an RC filter should be applied to this pin, such as
is shown in Figure 24. At this time, a delay time occurs due to the RC filter when the CS pin is detected.
Even if there is no filter, attachment of RCS as a surge countermeasure is recommended.
The recommended resistance for Rcs is 1 k. When a filter ring is desired, use Ccs to adjust for this resistance.
Figure24. Circuits Peripheral to the CS Pin
(7) CS pin open protection
When the CS pin (pin 4) has become an open pin, transient heat (due to noise, etc.) occurs in the IC, which may become
damaged.
An open protection circuit has been built in to prevent such damage. (Auto recovery protection)
Timeout
Bottom det OR
AND
VCCOVP
SQ
FBOLP_OH AND
R
POUT
PRE
Driver
NOUT
5 OUT
VREF(4V)
1MΩ
CURRENT SENSE
(V-V Change)
Normal : ×1.0
Leading
Edge
Blanking
3 CS
RS
Figure 25. CS Pin Peripheral Circuit
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
16/27
TSZ02201-0F2F0A200200-1-2
30.Oct.2013.Rev.001










页数 30 页
下载[ BM1P066FJ.PDF 数据手册 ]


分享链接

Link :

推荐数据表

零件编号描述制造商
BM1P066FJPWM Control ICROHM Semiconductor
ROHM Semiconductor

零件编号描述制造商
STK15C88256-Kbit (32 K x 8) PowerStore nvSRAMCypress Semiconductor
Cypress Semiconductor
NJM4556DUAL HIGH CURRENT OPERATIONAL AMPLIFIERNew Japan Radio
New Japan Radio
EL1118-G5 PIN LONG CREEPAGE SOP PHOTOTRANSISTOR PHOTOCOUPLEREverlight
Everlight


DataSheet8.cn    |   2020   |  联系我们   |   搜索  |  Simemap